background image

186 431.1 - BA DOMINATOR 68 S 

3.1.1

General Information

ROAD TRAFFIC REGULATIONS

NIn addition to his driving licence, the operator must 
always carry the copy of the vehicle type approval 
registration issued by the Kraftfahrt-Bundesamt 
(Federal Motor Vehicle Executive), a warning 
triangle and, on machines over 4 t permissible total 
weight, at least one wheel chock on the combine.

When driving on public roads with the combine, 
comply with all the requirements stated under letter 
C in the copy of the vehicle type approval regis-
tration (§18 Section 5 StVZO) issued by the 
Kraftfahrt-Bundesamt (Federal Motor Vehicle 
Executive).

On machines with exceptional width (width over 
tyres), a vehicle type approval registration for 
individual vehicles (single expert opinion) and an 
special approval in accordance with §70, Section 1, 
clauses 1 and 2 of the StVZO must be carried 
instead of the General Operating Permit. Fur-
thermore, all the requirements stated in the vehicle 
type approval registration for individual vehicles and 
in the special approval must be observed. The issue 
of a special approval differs from country to country. 
The excess width must be marked in accordance 
with the regulations for the marking of road vehicles 
with excess width (two warning panels at the front 
and back, protective bar, two warning lights for 
yellow flashing (rotaflare) lights.

If any parts of the combine are subsequently 
modified whose condition is prescribed or the 
operation of which (after being modified) could 
represent a hazard to other road users, then the 
vehicle type approval registration shall no longer be 
valid and application must be made for a new 
vehicle type approval registration. In this case the 
machine must be presented to the motor vehicle 
safety inspection authority responsible (TÜV) in 
order to obtain an expert opinion certificate 
(§19 section 2 STVZO).

If you are in any doubt as to whether this situation 
applies in your case, please contact us as manu-
facturers.

If a transport vehicle for attachments is towed 
behind the combine then the cable for the lighting 
system must be connected and the good condition 
of the lighting system assured.

If the combine is equipped with a maize header or 
folding cutterbar, the regulations and requirements 
of the General Operating Permit must be observed, 
in particular the requirements concerning ballast 
weights and tyres.

Registration

As a self-propelled working machine with a 
maximum speed of less than 20 kph the combine is 
not subject to the normal registration regulations 
and is not required to bear a registration plate. The 
machine must, however, be clearly and indelibly 
marked on the left-hand side with the christian name 
and surname of the owner and his address.

The towing of trailers in the trailer hitch when driving 
on public roads is not permitted.

Road traffic regulations may vary between 
countries. In case of discrepancies between the 
instructions provided by the manufacturer and the 
traffic regulations of the relevant countries, the 
traffic regulations of the countries concerned apply.

General Information

Содержание DOMINATOR 68 S
































Отзывы: