Citizen iDP-3110 Скачать руководство пользователя | Manualshive

Страница: 10 / 36

background image

iDP3110 User's Manual

CITIZEN

5

3.2 Part Descriptions

1. DC Jack

Insert the output plug of the AC adapter attached.

2. Power Switch

When switched ON, power is supplied to the printer, starting the initializing operation.

3. Power Lamp

Lighted when power is turned ON and goes out when turned OFF.

4. SEL Lamp

Lighted when printer is in the selected condition (ON-LINE).

Printer becomes operational only when this lamp is on.

5. LF Switch

Paper is fed when switch is pressed (de-select condition only). Used to supply paper or to
insert some space in the output.

6. SEL Switch

Printer is selected (ON-LINE) by pressing this switch.

Printer is de-selected (OFF-LINE) by pressing the switch again.

7. Interface Connector

Printer is connected to various hosts via cables.

Please ensure that both the printer and the host are turned off before connecting.

8. Printer Cover

Opened to exchange ribbon cassette and paper roll.

«
...
8
9
10
11
12
...
»

Содержание iDP-3110





































Отзывы:

Нет отзывов

Похожие инструкции для iDP-3110

Бренд: Lanier Страницы: 6

Бренд: Canon Страницы: 30

Бренд: Objet Страницы: 122

Бренд: Kyocera Страницы: 392

ActionLaser 1000

Бренд: Epson Страницы: 70

ActionLaser 1000

Бренд: Epson Страницы: 7

ActionLaser ActionLaser II

Бренд: Epson Страницы: 11

ActionLaser 1300

Бренд: Epson Страницы: 2

ActionLaser 1100

Бренд: Epson Страницы: 89

ActionLaser 1300

Бренд: Epson Страницы: 106

ActionLaser 1000

Бренд: Epson Страницы: 157

ActionLaser 1600

Бренд: Epson Страницы: 181

ActionLaser 1600

Бренд: Epson Страницы: 215

Бренд: Creality Страницы: 16

ActionLaser 1500

Бренд: Epson Страницы: 1

magicolor 2430 DL

Бренд: Konica Minolta Страницы: 140

Бренд: Brother Страницы: 174

Бренд: Hi-Touch Imaging Technologies Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды