Citizen CL-E700 Series Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 236

background image

Chapter 2 Operating Principles

2-2.

Operation of Control Parts

2-29

CL-E700 series

(5)

Ribbon motor temperature sensor

The ribbon motor temperature sensor is used to detect the temperature of the “SA Ribbon
Motor F” on the ribbon take-up side. This sensor is a thermistor bonded to the “SA Ribbon
Motor F”.
Since the resistance of the thermistor changes according to the temperature change, the
voltage at pin 99 (TMPRIB) of the CPU (U1A) changes accordingly. The CPU senses the
voltage at pin 99 (TMPRIB) to detect the temperature of the “SA Ribbon Motor F”.

Printing operation when the “SA Ribbon Motor F” temperature rises:

When the temperature of the “SA Ribbon Motor F” reaches 85



C (185



F), the “SA Ribbon

Motor F” stops after printing the current label.
In this case, the LED on the operation panel blinks in red and the LCD displays “Error RBMotor
Hot”, and the printer goes off-line. When the temperature of the “SA Ribbon Motor F” falls
below 80



C (176



F), the LED and LCD returns to normal display, and printing automatically

resumes.

Abnormally high temperature detection:

To protect the “SA Ribbon Motor F” from being damaged, an abnormally high temperature
detection circuit is provided. If the temperature of the “SA Ribbon Motor F” exceeds a set
temperature limit, the LED on the operation panel blinks in red and the LCD displays “Error
System Fail”, and the printer goes off-line. To recover from the error status, turn OFF the
printer once and then turn it ON.
A reference voltage, i.e., an allowable temperature limit, is applied to pin 2 of the comparator
(U8A), while the sensor output voltage (TMPRIB) from the ribbon motor temperature sensor is
applied to pin 3.

80



C

(176



F)

85



C

(185



F)

Normal speed

(Stop)

Normal speed

Normal speed

(Stops)

24

J4

M

Thermistor

R75

C103

R76

AN5

99

[SA Ribbon Motor F]

TMPRIB

+3.3V

2

J603

1

[SA Ribbon
Control PCB]

13

J601

RBMTH

CPU

13

J304

3-6

J301

24 TMP_RIB

[SA Relay PCB]

U1A

14-16

14-16

U8A

-

+

3
2

1

+3.3V

[SA Main PCB]

TEMP ERROR Detection

BA2903SFVM

R34

+3.3V

R32

C49

R33

N3

K1

33_N3

21_K1

FPGA

nTMPERR

nTMPENB

Error: Low

U5

nTMPERR

TMPRIB

3-6

(L: Disables ribbon motor drive.)

Ribbon Motor
Temperature Sensor

«
...
41
42
43
44
45
...
»

Содержание CL-E700 Series













































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CL-E700 Series

Бренд: Jamex Страницы: 10

Бренд: PERCo Страницы: 22

Бренд: Symbol Страницы: 249

Бренд: TrekStor Страницы: 56

Бренд: Symbol Страницы: 208

Invexs 170 Series

Бренд: Nedap Страницы: 4

Бренд: AEG Страницы: 17

Бренд: Panasonic Страницы: 2

ePassport Reader JT-P100

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 6

Camescope KV-S1025C

Бренд: Panasonic Страницы: 8

Бренд: S4A Страницы: 2

Бренд: Beinteractive Страницы: 13

Бренд: Capital Candy Company Страницы: 2

Бренд: ARKSCAN Страницы: 17

Бренд: ARKSCAN Страницы: 17

Бренд: ARKSCAN Страницы: 348

Бренд: U-Line Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды