Cisco XR 1200 series Скачать руководство пользователя страница 176

Страница: 176 / 432

maximum hops

To set the number of hops in which statistics are maintained for each path for the IP SLA operation, use the

maximum hops

command in IP SLA operation statistics configuration mode. To use the default value, use

the

form of this command.

maximum hops hops

no maximum hops

Syntax Description

Number of hops for which statistics are maintained for each path. Range is 1 to 30. Default
value is 16 for path operations; for example,

pathecho

hops

Command Default

The default value is 16 hops.

Command Modes

IP SLA operation statistics configuration

Command History

Modification

Release

This command was introduced

Release 3.3.0

Usage Guidelines

The

maximum hops

command is supported only when you configure path operations and the IP SLA ICMP

path-echo operation.

Task ID

Operations

Task ID

read, write

monitor

Examples

The following example shows how to set the number of hops for the statistics for the

maximum

command:

RP/0/0/CPU0:router#

configure

RP/0/0/CPU0:router(config)#

ipsla

RP/0/0/CPU0:router(config-ipsla)#

operation 1

RP/0/0/CPU0:router(config-ipsla-op)#

type icmp path-echo

RP/0/0/CPU0:router(config-ipsla-icmp-path-echo)#

statistics hourly

RP/0/0/CPU0:router(config-ipsla-op-stats)#

maximum hops 20

Cisco IOS XR System Monitoring Command Reference for the Cisco XR 12000 Series Router, Release 4.1

164

OL-24735-01

IP Service Level Agreement Commands

maximum hops

Содержание XR 1200 series

















































































































































































































































































































































































































































Результаты поиска

Содержание XR 1200 series

Отзывы:

Похожие инструкции для XR 1200 series

Бренды по названию

Популярные бренды

Cisco XR 1200 series, Справочник по командам

Результаты поиска

Содержание XR 1200 series

Отзывы:

Похожие инструкции для XR 1200 series

Бренды по названию

Популярные бренды