Cisco WRP500 Скачать руководство пользователя страница 72

Страница: 72 / 128

R E V I E W D R A F T # 1 — C I S C O C O N F I D E N T I A L

A-28

Cisco WRP500 Administration Guide

Appendix A Advanced Voice Fields

Line page

You can use the

Voice tab > Line

page to configure the lines for voice service. This page includes

the following sections:

•

“Line Enable section” section on page A-29

•

“Streaming Audio Server (SAS) section” section on page A-29

•

“NAT Settings section” section on page A-30

•

“Network Settings section” section on page A-31

Caller ID Method

The following choices are available:

•

Bellcore (N.Amer,China)

—CID, CIDCW, and VMWI. FSK sent

after first ring (same as ETSI FSK sent after first ring) (no polarity
reversal or DTAS).

•

DTMF (Finland, Sweden)

—CID only. DTMF sent after polarity

reversal (and no DTAS) and before first ring.

•

DTMF (Denmark)

—CID only. DTMF sentbefore first ring with no

polarity reversal and no DTAS.

•

ETSI DTMF

—CID only. DTMF sent after DTAS (and no polarity

reversal) and before first ring.

•

ETSI DTMF With PR

—CID only. DTMF sent after polarity reversal

and DTAS and before first ring.

•

ETSI DTMF After Ring

—CID only. DTMF sent after first ring (no

polarity reversal or DTAS).

•

ETSI FSK

—CID, CIDCW, and VMWI. FSK sent after DTAS (but no

polarity reversal) and before first ring. Waits for ACK from CPE after
DTAS for CIDCW.

•

ETSI FSK With PR (UK)

—CID, CIDCW, and VMWI. FSK is sent

after polarity reversal and DTAS and before first ring. Waits for ACK
from CPE after DTAS for CIDCW. Polarity reversal is applied only if
equipment is on hook.

The default is Bellcore(N.Amer, China).

Caller ID FSK
Standard

The WRP500 supports bell 202 and v.23 standards for caller ID
generation. Select the FSK standard you want to use, bell 202 or
v.23.

The default is bell 202.

Feature Invocation
Method

Select the method you want to use, Default or Sweden default. The
default is Default.

Содержание WRP500

































































































































Результаты поиска

Содержание WRP500

Отзывы:

Похожие инструкции для WRP500

Бренды по названию

Популярные бренды

Cisco WRP500, Руководство администратора

Результаты поиска

Содержание WRP500

Отзывы:

Похожие инструкции для WRP500

Бренды по названию

Популярные бренды