Cisco WLC 5700 Series Скачать руководство пользователя

Страница: 68 / 82

switchport

To put an interface that is in Layer 3 mode into Layer 2 mode for Layer 2 configuration, use the

switchport

command in interface configuration mode. To put an interface in Layer 3 mode, use the

form of this

command.

switchport

no switchport

Syntax Description

This command has no arguments or keywords.

Command Default

By default, all interfaces are in Layer 2 mode.

Command Modes

Interface configuration

Command History

Modification

Release

This command was introduced.

Cisco IOS XE 3.2SE

Usage Guidelines

Use the

no switchport

command (without parameters) to set the interface to the routed-interface status and

to erase all Layer 2 configurations. You must use this command before assigning an IP address to a routed
port.

This command is not supported on controllers running the LAN Base feature set.

Note

Entering the

no switchport

command shuts the port down and then reenables it, which might generate messages

on the device to which the port is connected.

When you put an interface that is in Layer 2 mode into Layer 3 mode (or the reverse), the previous configuration
information related to the affected interface might be lost, and the interface is returned to its default
configuration.

If an interface is configured as a Layer 3 interface, you must first enter the

switchport

command to

configure the interface as a Layer 2 port. Then you can enter the

switchport access vlan

and

switchport

mode

commands.

Note

The

switchport

command is not used on platforms that do not support Cisco-routed ports. All physical ports

on such platforms are assumed to be Layer 2-switched interfaces.

You can verify the port status of an interface by entering the

show running-config

privileged EXEC command.

Layer 2/3 Command Reference, Cisco IOS XE Release 3E (Cisco WLC 5700 Series)

OL-32323-01

Layer 2/3 Commands

switchport

Содержание WLC 5700 Series



















































































Результаты поиска

Содержание WLC 5700 Series

Отзывы:

Похожие инструкции для WLC 5700 Series

Бренды по названию

Популярные бренды

Cisco WLC 5700 Series, Справочник по командам

Результаты поиска

Содержание WLC 5700 Series

Отзывы:

Похожие инструкции для WLC 5700 Series

Бренды по названию

Популярные бренды