Cisco WLC 5700 Series Скачать руководство пользователя | Manualshive

Страница: 40 / 82

background image

lacp system-priority

To configure the system priority for the Link Aggregation Control Protocol (LACP), use the

lacp

system-priority

command in global configuration mode on the controller. To return to the default setting,

use the

no

form of this command.

lacp system-priority priority

no lacp system-priority

Syntax Description

System priority for LACP. The range is 1 to 65535.

priority

Command Default

The default is 32768.

Command Modes

Global configuration

Command History

Modification

Release

This command was introduced.

Cisco IOS XE 3.2SE

Usage Guidelines

The

lacp system-priority

command determines which controller in an LACP link controls port priorities.

An LACP channel group can have up to 16 Ethernet ports of the same type. Up to eight ports can be active,
and up to eight ports can be in standby mode. When there are more than eight ports in an LACP channel group,
the controller on the controlling end of the link uses port priorities to determine which ports are bundled into
the channel and which ports are put in hot-standby mode. Port priorities on the other controller (the
noncontrolling end of the link) are ignored.

In priority comparisons, numerically lower values have a higher priority. Therefore, the system with the
numerically lower value (higher priority value) for LACP system priority becomes the controlling system. If
both controllers have the same LACP system priority (for example, they are both configured with the default
setting of 32768), the LACP system ID (the controller MAC address) determines which controller is in control.

The

lacp system-priority

command applies to all LACP EtherChannels on the controller.

Use the

show etherchannel summary

privileged EXEC command to see which ports are in the hot-standby

mode (denoted with an H port-state flag in the output display).

Examples

This example shows how to set the LACP system priority:

Controller(config)#

lacp system-priority 20000

You can verify your settings by entering the

show lacp sys-id

privileged EXEC command.

Layer 2/3 Command Reference, Cisco IOS XE Release 3E (Cisco WLC 5700 Series)

32

OL-32323-01

Layer 2/3 Commands

lacp system-priority

«
...
38
39
40
41
42
...
»

Содержание WLC 5700 Series



















































































Отзывы:

Нет отзывов

Похожие инструкции для WLC 5700 Series

Бренд: Ubiquiti Страницы: 24

Бренд: Keithley Страницы: 59

Бренд: Hawking Страницы: 2

MediaStream ConnectPlus 1000

Бренд: Avid Technology Страницы: 74

Бренд: NETGEAR Страницы: 2

FieldPoint cFP-RTD-122

Бренд: National Instruments Страницы: 15

Бренд: Tripp Lite Страницы: 3

Бренд: Abocom Страницы: 2

Бренд: Comtrend Corporation Страницы: 4

Бренд: Linksys Страницы: 6

Бренд: MaxComm Страницы: 10

Q-SYS QIO-GP8x8

Бренд: QSC Страницы: 13

LOYTEC LIP‑3ECTC

Бренд: DELTA GROUP Страницы: 4

Бренд: bintec elmeg Страницы: 32

Бренд: Tenda Страницы: 74

Бренд: AMCI Страницы: 55

Бренд: Tripp Lite Страницы: 2

Бренд: Datacom Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды