Cisco WLC 5700 Series Скачать руководство пользователя

Страница: 11 / 82

About This Mode

Exit Method

Prompt

Access Method

Mode

Line configuration

Use this mode to
configure
parameters for the
terminal line.

To exit to global
configuration mode,
enter

exit

To return to
privileged EXEC
mode, press

Ctrl-Z

or enter

end

Controller(config-line)#

While in global
configuration mode,
specify a line with
the

line vty

line

console

command.

For more detailed information on the command modes, see the command reference guide for this release.

Understanding the Help System

You can enter a question mark (?) at the system prompt to display a list of commands available for each
command mode. You can also obtain a list of associated keywords and arguments for any command.

Table 2: Help Summary

Purpose

Command

Obtains a brief description of the help system in any
command mode.

help

Obtains a list of commands that begin with a
particular character string.

abbreviated-command-entry ?

Controller#

di?

dir disable disconnect

Completes a partial command name.

abbreviated-command-entry

<Tab>

Controller#

sh conf

<tab>

Controller#

show configuration

Lists all commands available for a particular
command mode.

Switch>

Lists the associated keywords for a command.

command ?

Switch>

show ?

Lists the associated arguments for a keyword.

command keyword ?

Controller(config)#

cdp holdtime ?

<10-255> Length of time (in sec) that

receiver must keep this packet

Layer 2/3 Command Reference, Cisco IOS XE Release 3E (Cisco WLC 5700 Series)

OL-32323-01

Using the Command-Line Interface

Understanding the Help System

Содержание WLC 5700 Series



















































































Результаты поиска

Содержание WLC 5700 Series

Отзывы:

Похожие инструкции для WLC 5700 Series

Бренды по названию

Популярные бренды

Cisco WLC 5700 Series, Справочник по командам

Результаты поиска

Содержание WLC 5700 Series

Отзывы:

Похожие инструкции для WLC 5700 Series

Бренды по названию

Популярные бренды