background image

Manually Connect a WAP571 or WAP571E to
the Network via Power Over Ethernet (PoE)

 

Objective

 

Connecting a Wireless Access Point (WAP)  to the same network as your computer would allow
them to communicate, thus, allowing you to configure the WAP. This is typically done when the
WAP is to be configured for the first time, or after the WAP has been reset, and will have to be
reconfigured. This article aims to show you the steps in connecting the WAP571 or WAP571E to
the network.
 

 
Applicable Devices

 

WAP500 Series – WAP571, WAP571E
 

 
Software Version

 

1.0.0.15 – WAP571, WAP571E
 

 
Connect the WAP571 to the Network via PoE

 

Important: Make sure that the network you are connecting the WAP to has PoE (802.3af and
802.3at) and that your network is up and running. 
 
Step 1. Connect one end of an Ethernet cable to the Ethernet port of a PoE switch, or router.
 
Step 2. Connect the other end of the Ethernet cable to the ETH0/PD port of the WAP571. 
 
Note: WAP571 bundles the two Ethernet ports to be in link aggregation mode. If the two Ethernet
ports have been connected at the same time, the link partner must also support link aggregation. 
 
Step 3. Check the lights on both the WAP571 and the PoE switch, or router. 
 
Note:
 

An orange light on the port of the PoE switch where the WAP571 is connected indicates that
the PoE switch is powering the WAP571.
A green light on the Ethernet port of the PoE switch where the WAP571 is connected
indicates a link between the devices.
A blinking green light on the front panel of the WAP571 indicates that the device is booting up.
A solid green light indicates that the WAP571 is ready and operational.
A solid green light on the Ethernet port of the WAP571 indicates a link between the switch and
the WAP571.
A blinking green light on the Ethernet port of the WAP571 indicates that the device is
receiving and transmitting data.
 

You should now have connected your WAP571E  to the network via PoE and can now proceed to
setting up the access point. For instructions, see Configure Basic Radio Settings on the WAP571

Содержание WAP500 Series







Отзывы: