Installing Cisco TelePresence System Codec C60
Page 1
78-19806-02 Codec C60 Installation Sheet | December 2012 | © 2010-2012 Cisco Systems, Inc. All rights reserved.
This box contains:
Codec C60
Top tray
TRC V remote control
A.
Rack profiles (2 pcs)
B.
Rack rear brackets (2 pcs)
C.
Rack extension brackets (2 pcs)
D.
Rack ear profiles (2 pcs)
Accessories box and cable kit
•
HDMI cable (3 m / 10 ft)
•
Ethernet cable (5 m / 16 ft)
•
Power cable (1.8 m / 6 ft)
•
Batteries LR03 AAA 1.5 V for the remote control
•
Screwdriver, combi 2 mm / 4 mm Allen Key (unbraco)
•
Screws (M6 and M3) and cage nuts (M6)
•
Universal rack brackets*
* Universal rack brackets: Use these only if the supplied rail based rack
mounting kit does not fit your type of rack.
User guides
The user documentation for this product, including compliance
and safety information, is available on the Cisco web site.
Go to:
http://www.cisco.com/go/cseries-docs
Rack mounting
WARRANTY:
Rack mounting the codec without using the
supplied mounting kit will void the warranty.
b)
Snap the cage
nuts to the rack.
1
Assembling the rack profiles
Slide the rack profiles A and B together.
3
Mounting the rack profiles to the rack
Mount the left and right rack profiles A+B(+C) to the rack. The screws,
screwdriver and cage nuts are found in the accessories box.
2
Optional: Assembling the extension rails
If the rack is deeper than the length of the
rack profiles A+B, then the extension rails C are
needed.
A+B
C
A
B
LEFT
RIGHT
d)
On both sides:
Fasten the rack profiles A+B
together, using one M3 screw on
each side.
Tool: Screwdriver, 2 mm Allen Key
a)
Mount the rack profiles in front
using two M6 screws on each side.
Tool: Screwdriver, 4 mm Allen Key
c)
Mount the rack
profiles on the rear
side using the M6
knob screws.
Mount the extension rail (C) to the
rack profiles (A+B) using M6 screws.
Tool: Screwdriver, 4 mm Allen Key
Details in front
Details on rear side
A
B
B
A
C
D
D
Remote Control
A
B
A+B
C
Please follow the steps in
this installation guide when
rack mounting the codec.
NOTE:
The profile should
be assembled with the
bend in the direction as
shown in the illustration.
NOTE:
If the supplied rack profiles are incompatible
with the rack, use the supplied universal rack
brackets.
Follow the instructions in step 4 on the next page
when assembling the universal rack brackets.
Rack mounting and connecting cables
TIP
If the menu is not already present,
press Home key or OK key on the
remote control to open the menu.
Navigate in the menu with the
arrow keys.
4
7
ghi
pqrs
6
#
abc/1
23
9
1
.
@
5
0
8
jkl
tuv
2
abc
3
def
mno
wxyz
EMC Class A declaration
WARNING:
This is a class A product. In a domestic environment this
product may cause radio interference in which case the user may be
required to take adequate measures.
声
明
此为
A
级产品，在生活环境中，该产品可能会造成无线电干扰。在这种
情况下，可能需要用户对其干扰采取切实可行的措施。
WARNING: This is a class A product. In a domestic environment
this product may cause radio interference in which case the user
may be required to take adequate measures.
