Cisco PA-VXA Series Скачать руководство пользователя страница 90 | Manualshive

Страница: 90 / 96

Cisco PA-VXA Series Скачать руководство пользователя страница 90

4-40

T1/E1 Digital Voice Port Adapter Installation and Configuration

OL-3592-02

Chapter 4 Configuring the PA-VXA, PA-VXB, and PA-VXC

Checking the Configuration

PA Bay 1 Information:

VXC-2T1/E1 Port adapter, 2 ports

EEPROM format version 1

HW rev 0.01, Board revision A0

Serial number: 15234366 Part number: 73-3861-03

Using the show interfaces Command

The show interfaces command displays status information (including the physical slot and interface
address) for the interfaces you specify. All of the examples that follow specify DSPfarm interfaces.

For complete descriptions of interface subcommands and the configuration options available for router
interfaces, refer to the publications listed in the

“Related Documentation” section on page viii

Note

The outputs that appear in this document may not match the output you receive when running these
commands. The outputs in this document are examples only.

Cisco 7200 Series and Cisco 7200 VXR Routers

Following is an example of the show interfaces DSPfarm command for Cisco 7200 series routers. In
this example, the PA-VXC-2TE1 port adapter is located in port adapter slot 1.

Router# show interfaces DSPfarm 1/0

DSPfarm1/0 is up, line protocol is up

Hardware is VXC-2T1/E1

MTU 256 bytes, BW 12000 Kbit, DLY 0 usec,

reliability 255/255, txload 1/255, rxload 1/255

Encapsulation ARPA, loopback not set

C549 DSP Firmware Version: MajorRelease.MinorRelease (BuildNumber)

DSP Boot Loader: 255.255 (255)

DSP Application: 3.2 (10)

Medium Complexity Application: 3.2 (12)

High Complexity Application: 3.2 (12)

Total DSPs 29, DSP0-DSP29, Jukebox DSP id 30

Down DSPs: none

Restarted DSPs due to background keep-alive failures DSPid(number of restart)e

Total sig channels 116 used 48, total voice channels 116 used 0

0 active calls, 24 max active calls, 163554 total calls

CHT: 489702 total sec, 2 avg sec, 69 max sec

230728928 rx packets, 0 rx drops, 239246561 tx packets, 0 tx frags

0 curr_dsp_tx_queued, 12 max_dsp_tx_queued

Last input never, output never, output hang never

Last clearing of "show interface" counters 4d20h

Queueing strategy: fifo

Output queue 0/0, 0 drops; input queue 0/75, 0 drops

5 minute input rate 0 bits/sec, 0 packets/sec

5 minute output rate 0 bits/sec, 0 packets/sec

228929291 packets input, 574310582 bytes, 0 no buffer

Received 0 broadcasts, 0 runts, 0 giants, 0 throttles

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort

239246561 packets output, 626450944 bytes, 0 underruns

0 output errors, 0 collisions, 0 interface resets

0 output buffer failures, 0 output buffers swapped out

Cisco 7401ASR Routers

Following is an example of the show interfaces DSPfarm command for Cisco 7401ASR routers. In this
example, the PA-VXB-2TE1+ port adapter is located in port adapter slot 1.

«
...
88
89
90
91
92
...
»

Содержание PA-VXA Series

































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды