Cisco PA-POS-2OC3 Скачать руководство пользователя страница 81

Страница: 81 / 100

4-13

PA-POS-2OC3 Two-Port Packet-over-SONET Port Adapter Installation and Configuration

OL-3028-06

Chapter 4 Configuring the PA-POS-2OC3

Checking the Configuration

Cisco 7304 Router—Example Output of the show version Command

Following is an example of the

show version

command from a Cisco 7304 router with the

Cisco PA-POS-2OC3 port adapter installed.

Router#

show version

Cisco Internetwork Operating System Software

IOS (tm) 7300 Software (C7300-JS-M), Version 12.2(20)S3, RELEASE SOFTWARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Compiled Thu 20-May-04 17:58 by pwade

Image text-base: 0x40008BF4, data-base: 0x427D2000

ROM: System Bootstrap, Version 12.1(12r)EX1, RELEASE SOFTWARE (fc1)

Currently running ROMMON from ROM 0

BOOTLDR: 7300 Software (C7300-JS-M), Version 12.2(20)S3, RELEASE SOFTWARE (fc2)

7304-1 uptime is 1 week, 6 days, 21 hours, 59 minutes

System returned to ROM by power-on

System image file is "disk0:c7300-js-mz.122-20.S3"

cisco 7300 (NSE100) processor (revision E) with 458752K/65536K bytes of memory.

Processor board ID SCA0606011G

R7000 CPU at 350Mhz, Implementation 39, Rev 3.3, 256KB L2, 1024KB L3 Cache

4 slot midplane, Version 65.48

Last reset from power-on

Bridging software.

X.25 software, Version 3.0.0.

TN3270 Emulation software.

PXF processor tmc0 'system:pxf/ucode1' is running ( v4.1 ).

PXF processor tmc1 'system:pxf/ucode1' is running ( v4.1 ).

1 FastEthernet/IEEE 802.3 interface(s)

2 Gigabit Ethernet/IEEE 802.3 interface(s)

1 ATM network interface(s)

2 Packet over SONET network interface(s)

509K bytes of non-volatile configuration memory.

31744K bytes of ATA compact flash in bootdisk (Sector size 512 bytes).

62976K bytes of ATA compact flash in disk0 (Sector size 512 bytes).

Configuration register is 0x2102

Cisco 7401ASR Router—Example Output of the show version Command

Following is an example of the

show version

command from a Cisco 7401ASR router with the

Cisco PA-POS-2OC3 port adapter installed.

Router#

show version

Cisco Internetwork Operating System Software

IOS (tm) 7400 Software (C7400-JS-M), Version 12.2(613), RELEASE SOFTWARE (fc1)

Compiled Sun 01-Dec-02 15:26 by prasath

Image text-base:0x600088F4, data-base:0x61F32000

ROM:System Bootstrap, Version 12.2(2r)DD, RELEASE SOFTWARE (fc1)

7401 uptime is 6 days, 15 hours, 25 minutes

System returned to ROM by reload at 02:46:08 UTC Thu Dec 19 2002

System image file is "disk0:c7400-js-mz"

Содержание PA-POS-2OC3





































































































Результаты поиска

Содержание PA-POS-2OC3

Отзывы:

Бренды по названию

Популярные бренды

Cisco PA-POS-2OC3, Руководство по установке и настройке

Результаты поиска

Содержание PA-POS-2OC3

Отзывы:

Бренды по названию

Популярные бренды