Cisco ONS 15454 Скачать руководство пользователя | Manualshive

Страница: 61 / 516

background image

If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the
unit in the rack.

Statement 1006

Warning

To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to
ensure that the system remains stable. The following guidelines are provided to ensure your safety:

•

This unit should be mounted at the bottom of the rack if it is the only unit in the rack.

•

When mounting this unit in a partially filled rack, load the rack from the bottom to the top with
the heaviest component at the bottom of the rack.

•

If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing
the unit in the rack. Statement 1006

Warning

To prevent airflow restriction, allow clearance around the ventilation openings to be at least:1 inch
(25.4 mm)

Statement 1076

Warning

The ONS 15454 must have 1 inch (25.4 mm) of airspace below the installed shelf assembly to allow air
flow to the fan intake. The air ramp (the angled piece of sheet metal on top of the shelf assembly)
provides this spacing and should not be modified in any way.

Statement 385

Warning

Voltages that present a shock hazard may exist on Power over Ethernet (PoE) circuits if interconnections
are made using uninsulated exposed metal contacts, conductors, or terminals. Avoid using such
interconnection methods, unless the exposed metal parts are located within a restricted access location
and users and service people who are authorized within the restricted access location are made aware
of the hazard. A restricted access area can be accessed only through the use of a special tool, lock and
key or other means of security.

Statement 1072

Warning

NTP-G306 Install the ONS 15454 Shelf

This procedure reverses the mounting bracket and mounts shelf assemblies in a
rack.

Purpose

Cisco ONS 15454 Hardware Installation Guide

31

Installing the ONS 15454 M12 (ANSI and ETSI) Shelf

NTP-G306 Install the ONS 15454 Shelf

«
...
59
60
61
62
63
...
»

Содержание ONS 15454





































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ONS 15454

Бренд: H&S Страницы: 32

Бренд: Televes Страницы: 50

Бренд: National Instruments Страницы: 43

Бренд: Philips Страницы: 87

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды