Cisco ONS 15454 Скачать руководство пользователя | Manualshive

Страница: 504 / 516

background image

• Operating temperature: 23 to 131 degrees Fahrenheit (-5 to +55 degrees Celsius)
• Operating humidity: 5 to 95 percent, noncondensing

Dimensions

The ONS 15454 M2 shelf assembly has these dimensions:

• Height: 3.5 inches (88.9 mm)
• Width: 19 or 23 inches (482.6 or 584.2 mm) with mounting ears attached
• Depth: 11.1 inches (281.94 mm)
• Weight:

• 11.02 pounds (5 kg) with preinstalled air filter and no cards installed
• 15.40 pounds (6.82 kg) with the power module, fan-tray assembly and air filter installed but with

no cards.

ONS 15454 M6 Shelf Specifications

This section provides specifications for shelf bandwidth; a list of topologies; Cisco Transport Controller (CTC)
specifications; the LAN, Transaction Language One (TL1), modem, and alarm specifications; timing, power,
and environmental specifications; and ONS 15454 M6 shelf dimensions.

Bandwidth

The ONS 15454 M6 has the following bandwidth specifications (depending on the applications):

• Total bandwidth: 600 Gbps
• Data plane bandwidth: 100 Gbps per slot

Configurations

The ONS 15454 M6 can be configured for the following dense wavelength division multiplexing (DWDM)
topologies:

• Hubbed rings
• Multihubbed rings
• Point-to-point
• Linear
• Linear with optical add/drop multiplexing (OADM)
• Hybrid terminal node
• Hybrid OADM node
• Hybrid line amplifier node
• Transponder Shelf
• Layer 2 aggregation shelf

Cisco ONS 15454 Hardware Installation Guide

474

Hardware Specifications

Dimensions

«
...
502
503
504
505
506
...
»

Содержание ONS 15454





































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ONS 15454

Бренд: National Instruments Страницы: 4

Supero SC808T-980B

Бренд: Supermicro Страницы: 66

Бренд: Supermicro Страницы: 80

ExpressBox EB3600-P

Бренд: Magma Страницы: 106

Бренд: Lantronix Страницы: 36

ViaLiteHD HRK3-HB-8

Бренд: ViaLite Страницы: 40

Бренд: Digitus Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды