manualshive.com logo in svg

Cisco ONS 15454, Руководство по установке оборудования

Поделиться
Скачать
Cisco ONS 15454 Скачать руководство пользователя страница 501

• Operating temperature: 32 to 131 degrees Fahrenheit (0 to +55 degrees Celsius)
• Operating humidity: 5 to 95 percent, noncondensing

Dimensions

The ONS 15454 ANSI shelf assembly has these dimensions:

• Height: 18.5 in. (40.7 cm)
• Width: 19 or 23 in. (41.8 or 50.6 cm) with mounting ears attached
• Depth: 12 in. (26.4 cm) (5 in. or 12.7 cm projection from rack)
• Weight: 55 lb (24.947 kg) empty

The ONS 15454 ETSI shelf assembly has the following dimensions:

• Height: 616.5 mm (24.27 in.)
• Width: 535 mm (17 in.) without mounting ears attached
• Depth: 280 mm (11.02 in.)
• Weight: 26 kg empty (57.3 lb)

ONS 15454 M2 Shelf Specifications

This section provides specifications for shelf bandwidth; a list of topologies; Cisco Transport Controller (CTC)
specifications; the LAN, Transaction Language One (TL1), modem, and alarm specifications; timing, power,
and environmental specifications; and shelf dimensions.

Bandwidth

The ONS 15454 M2 has these bandwidth specifications (depending on the applications):

• Total bandwidth: 200 Gbps
• Data plane bandwidth: 100 Gbps per slot

Configurations

The ONS 15454 M2 can be configured for these dense wavelength division multiplexing (DWDM) topologies:

• Hubbed rings
• Multihubbed rings
• Point-to-point
• Linear
• Linear with optical add/drop multiplexing (OADM)
• Line amplifier node
• Transponder Shelf
• Layer 2 aggregation shelf

Cisco Transport Controller

CTC, the ONS 15454 M2 craft interface software, has these specifications:

Cisco ONS 15454 Hardware Installation Guide

471

Hardware Specifications

Dimensions

Содержание ONS 15454





































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды