Cisco ONS 15454 Скачать руководство пользователя

Страница: 469 / 516

Step 13

If you removed the door, complete the

NTP-G40 Replace the Front Door , on page 448

. If not, close and lock

the door.

Stop. You have completed this procedure.

NTP-G274 Replace the Air Filter of the ONS 15454 M2 Shelf
Assembly

This procedure replaces the air filter of the ONS 15454 M2 shelf assembly.

Purpose

New air filter

Tools/Equipment

•

NTP-G266 Install the ONS 15454 M2 Shelf, on page 194

• Connect the chassis to the office ground. For detailed instructions on how

to ground the chassis, refer to the

Electrostatic Discharge and Grounding

Guide for Cisco CPT and Cisco ONS Platforms

Prerequisite Procedures

As Needed

Required/As Needed

Remote

Onsite/Remote

Provisioning or higher

Security Level

The air filters are single-use only. They must not be cleaned and reused. This is a Telcordia NEBS requirement,
GR-63-CORE Issue 4.

Note

Air filters must be inspected every month. If they are dirty or clogged with dust, they must be replaced with
a new air filter.

Note

Procedure

Step 1

Untighten the screw on the air-filter (see the following figure).

Cisco ONS 15454 Hardware Installation Guide

439

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

NTP-G274 Replace the Air Filter of the ONS 15454 M2 Shelf Assembly

Содержание ONS 15454




































































































































































































































































































































































































































































































































Результаты поиска

Содержание ONS 15454

Отзывы:

Похожие инструкции для ONS 15454

Бренды по названию

Популярные бренды

Cisco ONS 15454, Руководство по установке оборудования

Результаты поиска

Содержание ONS 15454

Отзывы:

Похожие инструкции для ONS 15454

Бренды по названию

Популярные бренды