Cisco ONS 15454 Скачать руководство пользователя | Manualshive

Страница: 235 / 516

background image

Figure 126: Mounting the Air Deflectors (Front-to-Front) on the ONS 15454 M2 Shelf for ETSI Rack Configuration

Step 16

Return to your originating procedure (NTP).

DLP-G587 Mounting the Bracket with Air Deflectors (Front-to-Back) on the ONS 15454 M2 Shelf
for ETSI Rack Configuration

This task installs the bracket with air deflectors (front-to-back) on the ONS 15454
M2 shelf for ETSI rack configuration.

Purpose

• #2 Phillips Dynamometric screwdriver
• Medium slot-head screwdriver
• Small slot-head screwdriver

Tools/Equipment

NTP-G305 Unpack and Inspect the ONS 15454, ONS 15454 M2, and ONS 15454
M6 Shelves, on page 20

Prerequisite Procedures

As needed

Required/As Needed

Onsite

Onsite/Remote

None

Security Level

Use only the fastening hardware provided with the ONS 15454 M2 to prevent loosening, deterioration, and
electromechanical corrosion of the hardware and joined material.

Caution

The air deflectors can be installed only in the front position of the chassis.

Note

Cisco ONS 15454 Hardware Installation Guide

205

Installing the ONS 15454 M2 Shelf

DLP-G587 Mounting the Bracket with Air Deflectors (Front-to-Back) on the ONS 15454 M2 Shelf for ETSI Rack Configuration

«
...
233
234
235
236
237
...
»

Содержание ONS 15454





































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ONS 15454

Бренд: HDanywhere Страницы: 30

Бренд: InWin Страницы: 23

Бренд: Advantech Страницы: 38

Бренд: Blonder tongue Страницы: 285

Бренд: ADLINK Technology Страницы: 43

Бренд: ADLINK Technology Страницы: 50

cPCIS-6418U Series

Бренд: ADLINK Technology Страницы: 66

Бренд: ASROCK Страницы: 1

Бренд: Keysight Страницы: 51

Бренд: MicroNet Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды