19-8
Cisco ONS 15454 Procedure Guide, R5.0
September 2005
Chapter 19 DLPs A200 to A299
DLP-A210 Change AIC-I Card Orderwire Settings
DLP-A210 Change AIC-I Card Orderwire Settings
Caution
When provisioning orderwire for ONS 15454s residing in a ring, do not provision a complete orderwire
loop. For example, a four-node ring typically has east and west ports provisioned at all four nodes.
However, to prevent orderwire loops, provision two orderwire ports (east and west) at all but one of the
ring nodes.
Tip
Before you begin, make a list of the ONS 15454 slots and ports that require orderwire communication.
Step 1
In node view, double-click the AIC-I card to display it in card view.
Step 2
Click the
Provisioning > Local Orderwire
tabs or the
Provisioning > Express Orderwire
tabs,
depending on the orderwire path that you want to create. Provisioning steps are the same for both types
of orderwire.
Step 3
If needed, adjust the Tx and Rx dBm by moving the slider to the right or left for the headset type
(four-wire or two-wire) that you will use. In general, you should not need to adjust the dBm.
Step 4
If you want to turn on the audible alert (buzzer) for the orderwire, check the
Buzzer On
check box.
Step 5
Click
Apply
.
Step 6
Return to your originating procedure (NTP).
DLP-A212 Create a User Data Channel Circuit
Step 1
In network view, click the
Provisioning > Overhead
Circuits
tabs.
Step 2
Click
Create
.
Purpose
This task changes orderwire settings on the AIC-I card.
Tools/Equipment
None
Prerequisite Procedures
DLP-A60 Log into CTC, page 17-66
Required/As Needed
As needed
Onsite/Remote
Onsite or remote
Security Level
Provisioning or higher
Purpose
This task creates a user data channel (UDC) circuit on the ONS 15454. A
UDC circuit allows you to create a dedicated data channel between nodes.
Tools/Equipment
OC-N cards must be installed.
Prerequisite Procedures
NTP-A24 Verify Card Installation, page 4-2
DLP-A60 Log into CTC, page 17-66
Required/As Needed
As needed
Onsite/Remote
Onsite or remote
Security Level
Provisioning or higher
Содержание ONS 15454 Series
