5-15
Cisco ONS 15454 Procedure Guide, R5.0
December 2004
Chapter 5 Turn Up Network
NTP-A176 Four-Fiber BLSR Acceptance Test
NTP-A176 Four-Fiber BLSR Acceptance Test
Caution
This procedure might be service affecting if performed on a node carrying traffic.
Note
This procedure requires that you create test circuits and perform a ring switch. For clarity, “Node 1”
refers to the login node where you begin the procedure. “Node 2” refers to the node connected to the east
OC-N trunk (span) card of Node 1, “Node 3” refers to the node connected to the east OC-N trunk card
of Node 2, and so on.
Step 1
Complete the
“DLP-A60 Log into CTC” task on page 17-66
on the BLSR you are testing. (This node
will be called Node 1.) If you are already logged in, continue with Step 2.
Step 2
From the View menu, choose
Go to Network View
.
Step 3
Click the
Alarms
tab.
a.
Verify that the alarm filter is not on. See the
“DLP-A227 Disable Alarm Filtering” task on
as necessary.
b.
Verify that no unexplained alarms appear on the network. If unexplained alarms appear, resolve
them before continuing. Refer to the
Cisco ONS 15454 Troubleshooting Guide
if necessary
.
c.
Complete the
“DLP-A516 Export CTC Data” task on page 22-6
to export the alarm information.
Step 4
Click the
Conditions
tab.
a.
Verify that no unexplained conditions appear on the network. If unexplained conditions appear,
resolve them before continuing. Refer to the
Cisco ONS 15454 Troubleshooting Guide
if necessary
.
b.
Complete the
“DLP-A516 Export CTC Data” task on page 22-6
to export the conditions
information.
Step 5
On the network map, double-click Node 1.
Step 6
Complete the
“DLP-A92 Four-Fiber BLSR Exercise Span Test” task on page 17-91
Step 7
Complete the
“DLP-A217 BLSR Exercise Ring Test” task on page 19-10
.
Step 8
Create a test circuit between Node 1 and Node 2.
•
For DS-1 circuits, complete the
“NTP-A181 Create an Automatically Routed DS-1 Circuit”
. When you set the circuit state, choose
IS
and check the
Apply to drop ports
check box.
•
For DS-3 circuits, complete the
“NTP-A184 Create an Automatically Routed DS-3 Circuit”
. When you set the circuit state, choose
IS
and check the
Apply to drop
ports
check box.
Purpose
This procedure tests a four-fiber BLSR.
Tools/Equipment
Test set and cables appropriate to the test circuit you will create
Prerequisite Procedures
NTP-A40 Provision BLSR Nodes, page 5-10
NTP-A126 Create a BLSR, page 5-12
Required/As Needed
As needed
Onsite/Remote
Onsite
Security Level
Provisioning and higher
Содержание ONS 15454 Series
