Cisco ONS 15454 M6 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 32

background image

MEA on fan tray

—

No

5A

15454E-SA-ETSI

MEA on fan tray and 10G cards

—

Yes

5A

15454E-SA-ETSI

None

—

No

5A

15454E-SA-ETSI

MEA on 10G

—

Yes

5A

15454E-SA-ETSI

None

—

No

2A

ETSI

MEA on fan tray or Ethernet

2.5G compatible

Yes

2A

ETSI

MEA on fan tray

10G compatible

Yes

2A

ETSI

None

Either

No

2A

ETSI

MEA on fan tray, Ethernet

2.5G compatible

Yes

2A

ETSI

MEA on fan tray

10G compatible

Yes

2A

ETSI

MEA on Ethernet

2.5G compatible

Yes

5A

ETSI

None

Either

No

5A

ETSI

None

Either

Yes

5A

ETSI

6

15454-SA-ETSI (P/N: 800-08708-XX) = ONS 15454 SDH Release 3.3 and later shelf assembly

7

5A Fan Tray = 15454E-FTA-60V, 15454E-CC-FTA2A Fan Tray = 15454E-FTA-48V

8

10G cards = XC10G, XC-VXL-10G, XC-VXC-10G

Step 2

Open the front door of the shelf assembly. If the shelf assembly does not have a front door, continue with
Step 4.

a) Open the front door lock.

The ONS 15454 comes with a pinned hex key for locking and unlocking the front door. Turn the key
counterclockwise to unlock the door and clockwise to lock it.

b) Press the door button to release the latch.
c) Swing the door open.

Step 3

(Optional) Complete the

DLP-G577 Remove the Standard Door of the ONS 15454 M6 Shelf

to remove the

front door. If you do not want to remove the door, proceed to Step 4.

Step 4

Push the outer side of the handles on the fan-tray assembly to expose the handles.

Step 5

Fold out the retractable handles at the outside edges of the fan tray.

Step 6

Pull the handles and slide the fan-tray assembly one inch (25.4 mm) out of the shelf assembly and wait until
the fans stop.

Step 7

When the fans have stopped, pull the fan-tray assembly completely out of the shelf assembly. The following
figure shows the location of the fan tray on the ONS 15454 ANSI shelf.

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

19

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

NTP-G116 Replace the Fan-Tray Assembly of the ONS 15454 Shelf Assembly

«
...
17
18
19
20
21
...
»

Содержание ONS 15454 M6

































Отзывы:

Нет отзывов

Похожие инструкции для ONS 15454 M6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды