manualshive.com logo in svg

Cisco ONS 15454 M6, Руководство по обслуживанию

Устройство Cisco ONS 15454 M6 - это надежное оборудование для сетей передачи данных, обеспечивающее высокую производительность. Для поддержания работы устройства в отличном состоянии, необходимо регулярно проводить техническое обслуживание. Вы можете скачать бесплатное Руководство по обслуживанию на manualshive.com.

Поделиться
Скачать
background image

None

Prerequisite Procedures

Required

Required/As Needed

Onsite

Onsite/Remote

None

Security Level

Procedure

Step 1

Remove the dust plug from the fiber adapter.

Step 2

Insert a CLETOP stick swab (14100400) into the adapter opening and rotate the swab.

Step 3

Place dust plugs on the fiber adapters when not in use.

Step 4

Return to your originating procedure (NTP).

NTP-G40 Replace the Front Door

This procedure replaces the front door and door ground strap after installing cards
and fiber-optic cables.

Purpose

#2 Phillips screwdriver

Medium slot-head screwdriver

Small slot-head screwdriver

Tools/Equipment

NTP-G259 Open and Remove the Standard Door of the ONS 15454 M6 Shelf

Prerequisite Procedures

Required

Required/As Needed

Onsite

Onsite/Remote

None

Security Level

Be careful not to crimp any fiber cables that are connected to the MXP/TXP cards or DWDM cards. Some
might not have the fiber boot attached.

Note

Procedure

Step 1

Insert the front door into the hinges on the shelf assembly.

Step 2

(ANSI only) Attach one end of the ground strap terminal lug (72-3622-01) to the male stud on the inside of
the door. Attach and tighten the #6 Kepnut (49-0600-01) using the open-end wrench.

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

14

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

NTP-G40 Replace the Front Door

Содержание ONS 15454 M6

































Отзывы:

Нет отзывов

Похожие инструкции для ONS 15454 M6

Бренды по названию

Популярные бренды

Загрузить еще бренды