Cisco ONS 15454 M6 Скачать руководство пользователя страница 69

Страница: 69 / 164

Stop. You have completed this procedure.

NTP-G329 Remove the Deep-Front Panel of the ONS 15454 M6
Shelf

This procedure removes the deep-front panel of the ONS 15454 M6 system.

Purpose

• #2 Phillips Dynamometric screwdriver
• Socket (6/32 standard) and socket wrench to tighten or loosen the ground

nut

Tools/Equipment

•

NTP-G252 Install the ONS 15454 M6 Shelf , on page 24

•

NTP-G327 Install the Deep-Front Panel of the ONS 15454 M6 Shelf, on
page 62

• Connect the chassis to the office ground. For detailed instructions on how

to ground the chassis, see the

Electrostatic Discharge and Grounding Guide

for Cisco CPT and Cisco ONS Platforms

Prerequisite Procedures

Required

Required/As Needed

Onsite

Onsite/Remote

None

Security Level

The deep-front panel does not have a hinge and cannot be rotated like a standard door. Rotating the deep-front
panel can damage the deep-front panel, shelf hinges, other devices and cables placed below the ONS 15454
M6 shelf.

Caution

When the deep front-panel is installed, the total chassis depth is 12.9 inches. The deep front-panel extends
from the rack by 1.8 inches.

Note

Procedure

Step 1

Remove the end of the ground strap cable that is connected to the exterior of the deep-front panel (see the
following figure).

Installing the ONS 15454 M6 Shelf

NTP-G329 Remove the Deep-Front Panel of the ONS 15454 M6 Shelf

Содержание ONS 15454 M6





































































































































































Результаты поиска

Содержание ONS 15454 M6

Отзывы:

Похожие инструкции для ONS 15454 M6

Бренды по названию

Популярные бренды

Cisco ONS 15454 M6, Руководство по установке

Результаты поиска

Содержание ONS 15454 M6

Отзывы:

Похожие инструкции для ONS 15454 M6

Бренды по названию

Популярные бренды