Cisco Nexus 9396PX Скачать руководство пользователя страница 67

Страница: 67 / 74

Power Supply LEDs

The power supply LEDs are located on the left front portion of the power supply. Combinations of states

indicated by the Okay (

) and Fault (

) LEDs indicate the status for the module as shown in the following

table.

Status

LED

Power supply is on and outputting power to the switch.

Off

Green

Power supply is connected to a power source but not outputting power to the
switch—power supply might not be installed in the chassis.

Off

Flashing
green

Power supply is not receiving power.

Off

Power supply warning—possibly one of the following conditions:

• High voltage

• High power

• Low voltage

• Power supply installed in chassis but not connected to a power source

• Slow power supply fan

Flashing amber

Green

Cisco Nexus 9396PX ACI-Mode Switch Hardware Installation Guide

LEDs

Power Supply LEDs

Содержание Nexus 9396PX











































































Результаты поиска

Содержание Nexus 9396PX

Отзывы:

Похожие инструкции для Nexus 9396PX

Бренды по названию

Популярные бренды

Cisco Nexus 9396PX, Руководство по установке оборудования

Результаты поиска

Содержание Nexus 9396PX

Отзывы:

Похожие инструкции для Nexus 9396PX

Бренды по названию

Популярные бренды