Cisco Nexus 92160YC-X Скачать руководство пользователя страница 60

Страница: 60 / 72

Cord Set Description

Power Cord Part Number

Power Type

250 V, 10 A, 8.2 feet (2.5 m)

CAB-250V-10A-IS

Israel

250 VAC, 10 A, CEI 23-16/VII
plug, 8.2 feet (2.5 m)

CAB-9K10A-IT

Italy

125 VAC, 13 A, NEMA 5-15 plug,
8.2 feet (2.5 m)

CAB-9K12A-NA

North America

NEMA L6-20-C13, 6.6 feet (2.0 m)

CAB-AC-L620-C13

North America

200/240V, 6A, 8.2 feet (2.5 m)

CAB-N5K6A-NA

North America

250 V, 10 A, 8.2 feet (2.5 m)

CAB-250V-10A-CN

Peoples Republic of China

250 V, 10 A, 8.2 feet (2.5 m)

CAB-250V-10A-ID

South Africa

250 VAC, 10 A, MP232 plug, 8.2
feet (2.5 m)

CAB-9K10A-SW

Switzerland

250 VAC, 10 A, BS1363 plug (13
A fuse), 8.2 (2.5 m)

CAB-9K10A-UK

United Kingdom

No power cord included with
switch

NO-POWER-CORD

All except Argentina, Brazil, and
Japan

HVAC/HVDC Power Cables Supported by ACI-Mode and NX-OS Mode Switches

Cord Set Description

Power Cord Part Number

Power Type

2-foot (0.6 m) cable with
Saf-D-Grid and SD connectors

CAB-HVAC-SD-0.6M

HVAC

6.6-foot (2.0 m) cable with
Saf-D-Grid and C14 connector (use
for up to 240 V)

CAB-HVAC-C14-2M

HVAC

2-foot (0.6 m) cable with
Saf-D-Grid and RT connector

CAB-HVAC-RT-0.6M

HVAC

6.6-foot (2.0 m) cable with
Saf-D-Grid and three terminal
connectors

CAB-HVDC-3T-2M

HVDC

No power cord included with
switch

NO-POWER-CORD

All except Argentina, Brazil, and
Japan

Cisco Nexus 9236C NX-OS Mode Switch Hardware Installation Guide

System Specifications

HVAC/HVDC Power Cables Supported by ACI-Mode and NX-OS Mode Switches

Содержание Nexus 92160YC-X









































































Результаты поиска

Содержание Nexus 92160YC-X

Отзывы:

Похожие инструкции для Nexus 92160YC-X

Бренды по названию

Популярные бренды

Cisco Nexus 92160YC-X, Руководство по установке оборудования

Результаты поиска

Содержание Nexus 92160YC-X

Отзывы:

Похожие инструкции для Nexus 92160YC-X

Бренды по названию

Популярные бренды