Cisco Nexus 2000 Series Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 190

background image

1-32

Cisco Nexus 2000 Series Hardware Installation Guide

Chapter 1 Using a Fabric Extender with a Cisco Nexus 5000 Series or Cisco Nexus 6000 Series Switch

Cisco Nexus 2224TP

Figure 1-33

Port-Side Intake Airflow Fan Tray for the Cisco Nexus 2232TM-10GE FEX

To replace a fan tray, see the

“Removing and Installing the Fan Tray” section on page 4-21

. For LED

descriptions, see

Table E-1 on page E-2

.

Supported Transceivers and Cables

The Cisco Nexus 2232TM-10GE Series FEX supports SFP+ Ethernet transceivers. The enhanced
Small-Form-Factor Pluggable (SFP+) 10-Gigabit Ethernet transceiver is a bidirectional device with a
transmitter and receiver. It has a 20-pin connector on the electrical interface and duplex LC connector
on the optical interface. Currently, the FEX supports the short-range SFP and long-range SFP
transceiver. Copper interface cables are available for use with the 10-Gigabit Ethernet SFP+ transceiver.
For an updated list of supported transceivers and optics, please see the

Cisco Nexus 2000 Series Fabric

Extenders Release Notes.

Cisco Nexus 2224TP

The Cisco Nexus 2224TP is a stackable 1 RU FEX. This FEX is very similar to the Cisco Nexus 2248TP
except that it has 24 100/1000BASE-T downlink ports, 2 SFP+ uplink ports and you can order it with
port-side exhaust airflow or port-side intake airflow. You can use this FEX with the Cisco Nexus 5000
Series switch. The Cisco Nexus 2224TP is managed and configured by the upstream switch. The FEX

1

Captive screws (2)

3

No black stripe indicates port-side exhaust
airflow

2

Handle

4

Status LED

239936

2

1

3

1

1

Captive screws (2)

3

Status LED

2

Black stripe indicates port-side intake airflow

«
...
48
49
50
51
52
...
»

Содержание Nexus 2000 Series































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Nexus 2000 Series

Бренд: EAW Страницы: 2

Netlink FRX4000

Бренд: Cabletron Systems Страницы: 8

Бренд: Cabletron Systems Страницы: 4

Бренд: Commell Страницы: 36

IntroSpect Analyzer 2 Series

Бренд: Aruba Страницы: 5

Millennium P650

Бренд: Matrox Страницы: 54

Бренд: RAIDAGE Страницы: 60

Бренд: 3Ware Страницы: 4

Бренд: Lutron Electronics Страницы: 4

Бренд: IEI Technology Страницы: 2

Бренд: Xantech Страницы: 5

SFD-2 MkIII Jumper

Бренд: Anthem Audio Страницы: 2

Бренд: V-Count Страницы: 2

DataFire GO! PRO

Бренд: Digi Страницы: 20

AdvancedTCA AT8901M

Бренд: Kontron Страницы: 76

Бренд: LaView Страницы: 2

Бренд: ExtraHop Страницы: 2

Бренд: RAID Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды