Cisco Network Storage System NSS3000 Series Скачать руководство пользователя страница 14

Страница: 14 / 184

Managing the System

System Alerts

Cisco Small Business NSS3000 Series Network Storage System Administration Guide

The following sections describe the information that appears on the

System

Status

page.

System Alerts

The

System

Alerts

section shows any system messages issued since the last

time they were cleared. Messages can range in severity from informational to
immediate action required.

There are three type of alerts that can appear:

•

Error

: Indicates the most severe types of problems with the NSS. They

require immediate action. For example, if a disk drive or RAID array is in a
failed condition.

•

Warning

: Indicates that there is a problem with the NSS that requires

eventual action. For example, if the amount of storage used for a volume is
over 90%.

•

Notification

: These types of messages are simply to advise of changes to

the NSS. For example, the RAID rebuild is complete.

Storage Status

The

Storage

area displays details about the configured storage on the NSS,

including:

•

Drives

: The number of physical disk drives installed.

•

RAID

Arrays

: The number of configured RAID arrays.

•

Volumes

: The number of configured volumes.

•

Total Configured Capacity

: The total aggregate size of all configured

volumes.

•

Percent

Used

: The total amount of the configured capacity used.

Содержание Network Storage System NSS3000 Series

























































































































































































Результаты поиска

Содержание Network Storage System NSS3000 Series

Отзывы:

Похожие инструкции для Network Storage System NSS3000 Series

Бренды по названию

Популярные бренды

Cisco Network Storage System NSS3000 Series, Руководство администратора

Результаты поиска

Содержание Network Storage System NSS3000 Series

Отзывы:

Похожие инструкции для Network Storage System NSS3000 Series

Бренды по названию

Популярные бренды