Cisco NCS 6000 Series Скачать руководство пользователя страница 170 | Manualshive

Страница: 170 / 498

Cisco NCS 6000 Series Скачать руководство пользователя страница 170

Purpose

Command or Action

Specifies the primary IPv4 address assigned to the bundle
interface on a connected remote system, where

ip-address

is the 32-bit IP address in dotted-decimal format (A.B.C.D).

bfd address-family ipv4 destination ip-address

Example:

RP/0/RP0/CPU0:router(config-if)# bfd address-family

ipv4 destination 10.20.20.1

Step 3

commit

Step 4

Enabling BFD Sessions on Bundle Members

To enable BFD sessions on bundle member links, complete these steps:

SUMMARY STEPS

1.

configure

2.

interface Bundle-Ether

|

Bundle-POS

]

bundle-id

3.

bfd address-family ipv4 fast-detect

4.

commit

DETAILED STEPS

Purpose

Command or Action

configure

Step 1

Enters interface configuration mode for the specified bundle
ID.

interface Bundle-Ether

|

Bundle-POS

]

bundle-id

Example:

Step 2

RP/0/RP0/CPU0:router(config)# interface
Bundle-Ether 1

Enables IPv4 BFD sessions on bundle member links.

bfd address-family ipv4 fast-detect

Example:

Step 3

RP/0/RP0/CPU0:router(config-if)# bfd address-family

ipv4 fast-detect

commit

Step 4

Configuring the Minimum Thresholds for Maintaining an Active Bundle

The bundle manager uses two configurable minimum thresholds to determine whether a bundle can be brought
up or remain up, or is down, based on the state of its member links.

• Minimum active number of links

• Minimum active bandwidth available

Whenever the state of a member changes, the bundle manager determines whether the number of active
members or available bandwidth is less than the minimum. If so, then the bundle is placed, or remains, in

Routing Configuration Guide for Cisco NCS 6000 Series Routers, IOS XR Release 6.4.x

148

Implementing BFD

Enabling BFD Sessions on Bundle Members

«
...
168
169
170
171
172
...
»

Содержание NCS 6000 Series



















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов