manualshive.com logo in svg

Cisco NCS 5700 Series, Руководство по установке оборудования

Поделиться
Скачать
Cisco NCS 5700 Series Скачать руководство пользователя страница 84

Electrical connection to
the module circuitry

3

40GBASE QSFP+
transceiver body

1

Bail-clasp latch

2

Required Tools and Equipment

You need these tools to install the 40-Gigabit QSFP+ / 100-Gigabit QSFP28 transceiver modules:

• Wrist strap or other personal grounding device to prevent ESD occurrences.

• Antistatic mat or antistatic foam to set the transceiver on.

• Fiber-optic end-face cleaning tools and inspection equipment.

Installing the 40-Gigabit QSFP+ or 100-Gigabit Transceiver Module

The QSFP+ or QSFP28 transceiver module can have either a bail-clasp latch or a pull-tab latch. Installation
procedures for both types of latches are provided.

The QSFP+ or QSFP28 transceiver module is a static-sensitive device. Always use an ESD wrist strap or
similar individual grounding device when handling QSFP+ or QSFP28 transceiver modules or coming into
contact with system modules.

Caution

To install an QSFP+ or QSFP28 transceiver module, follow these steps:

Step 1

Attach an ESD wrist strap to yourself and a properly grounded point on the chassis or the rack.

Step 2

Remove the QSFP+ or QSFP28 transceiver module from its protective packaging.

Step 3

Check the label on the QSFP+ or QSFP28 transceiver module body to verify that you have the correct model for your
network.

Step 4

For optical QSFP+ or QSFP28 transceiver modules, remove the optical bore dust plug and set it aside.

Step 5

For QSFP+ or QSFP28 transceiver modules equipped with a pull-tab, hold the transceiver so that the identifier label is
on the top.

Step 6

For QSFP+ or QSFP28 transceiver modules equipped with a bail-clasp latch, keep the bail-clasp aligned in a vertical
position.

Step 7

Align the QSFP+ or QSFP28 transceiver module in front of the module’s transceiver socket opening and carefully slide
the QSFP+ or QSFP28 transceiver into the socket until the transceiver makes contact with the socket electrical connector
(see the figure below).

Hardware Installation Guide for Cisco NCS 5700 Series Fixed-Port Routers

78

Connect Router to the Network

Required Tools and Equipment

Содержание NCS 5700 Series

























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды