Cisco NCS 5700 Series Скачать руководство пользователя страница 65

Страница: 65 / 120

Figure 47: NCS-57C3-MOD - Connecting DC Power

Step 3

Dress the power according to local practice.

Step 4

Connect the office battery and return cables according to the fuse panel engineering specifications.

Step 5

Insert the DC connector into the DC receptacle on the power supply.

After the connection, the black color (DC negative) wire appears on top.

To connect the PSU2KW-DCPI power supply module with the power source, you must procure the
PWR-2KW-DC-CBL power cord.

Note

To connect the NC57-1600W-DCFW power supply module with the power source, you must procure the
CAB-48DC-40A-8AWG power cord.

Note

Step 6

Ensure that the locking mechanism has engaged to secure the cable.

Step 7

Turn on the circuit breaker at the power source.

Power Supply Unit Input and Output Ranges

This table summarises input and output power ranges for PSU low line and nominal applications:

Table 11: Input and output power ranges for PSUs

Output

Output Power

Input Current (Max)

Input Voltage

PID

12V/84A

1000W

12A

100-127V ac

PSU2KW-ACPI

For low line
applications

Hardware Installation Guide for Cisco NCS 5700 Series Fixed-Port Routers

Install the Chassis

Power Supply Unit Input and Output Ranges

Содержание NCS 5700 Series
























































































































Результаты поиска

Содержание NCS 5700 Series

Отзывы:

Бренды по названию

Популярные бренды

Cisco NCS 5700 Series, Руководство по установке оборудования

Результаты поиска

Содержание NCS 5700 Series

Отзывы:

Бренды по названию

Популярные бренды