Cisco NCS 5700 Series Скачать руководство пользователя страница 113

Страница: 113 / 120

Status

Color

LED

The port is active.

Green

Link (for
each port)

The port is disabled by the operator or is not initializing.

Orange

The port is faulty and disabled.

Flashing orange

The port is not active or the link is not connected.

Off

Management Port LEDs

The Management Port LEDs are located at the right-side on the front panel of the chassis.

Figure 80: Management Port LEDs

Port Activity

Port Link

Table 18: Management Port LEDs Description

Status

Color

LED

The ethernet link is up and operational.

Green

Port Activity

The ethernet link is down.

Off

The port is either receiving or transmitting packets.

Green
Blinking

Port Link

No packets are being received or transmitted.

Off

Hardware Installation Guide for Cisco NCS 5700 Series Fixed-Port Routers

107

LEDs

Management Port LEDs

Содержание NCS 5700 Series
























































































































Результаты поиска

Содержание NCS 5700 Series

Отзывы:

Бренды по названию

Популярные бренды

Cisco NCS 5700 Series, Руководство по установке оборудования

Результаты поиска

Содержание NCS 5700 Series

Отзывы:

Бренды по названию

Популярные бренды