Cisco NCS 5501 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 82

background image

are properly installed in the correct order. For information about a step, see the respective section of this
installation guide.

Figure 1: Installation Workflow

Review Safety Guidelines

Before you perform any procedure in this document, review the safety guidelines in this section to avoid
injuring yourself or damaging the equipment. The following guidelines are for your safety and to protect
equipment. The guidelines do not include all hazards. Be alert.

•

Keep the work area clear, smoke and dust-free during and after installation. Do not allow dirt or debris
to enter into any laser-based components.

•

Do not wear loose clothing, jewelry, or other items that could get caught in the router or other associated
components.

•

Cisco equipment operates safely when used in accordance with its specifications and product-usage
instructions.

•

Be sure to power down a fixed configuration PDU or modular configuration power shelf before removing
it from the chassis.

•

Do not work alone if potentially hazardous conditions exist.

Hardware Installation Guide for Cisco NCS 5500 Series Fixed-Port Routers

4

Prepare for Installation

Review Safety Guidelines

«
...
10
11
12
13
14
...
»

Содержание NCS 5501



















































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 5501

Бренд: D-Link Страницы: 32

Бренд: D-Link Страницы: 6

Бренд: D-Link Страницы: 221

ShareCenter Pro DNS-1200-05

Бренд: D-Link Страницы: 68

Express Ethernetwork DI-707P

Бренд: D-Link Страницы: 14

Бренд: Sagem Страницы: 19

Бренд: Icidu Страницы: 10

Бренд: XAVI Technologies Corp. Страницы: 71

Бренд: Niveo Страницы: 155

Бренд: Premio Страницы: 3

Бренд: RAIDAGE Страницы: 60

RP614 - Web Safe Router

Бренд: NETGEAR Страницы: 16

Бренд: Tripp Lite Страницы: 2

24-Port 1000BASE-T

Бренд: Comet Labs Страницы: 44

Бренд: 2N Telekomunikace Страницы: 67

Бренд: Dynamix Страницы: 102

Бренд: Intellinet Страницы: 2

Бренд: FOR-A Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды