Cisco NCS 2000 series Скачать руководство пользователя страница 485 | Manualshive

Страница: 485 / 602

background image

Step 2

Click the

Provisioning

>

Line

>

Wavelength Trunk Provisioning

tabs.

Step 3

In the Wavelength field, view the provisioned card wavelength.

Step 4

If you have access to the site, compare the wavelength listed on the card faceplate with the provisioned wavelength. If
you are remote, compare this wavelength with the card identification in the inventory:

a) In node view (single-shelf mode) or shelf view (multishelf mode), click the

Inventory

tab.

b) Locate the slot where the TXP or MXP card is installed and view the card wavelength in the name.

Step 5

If the card was provisioned for the wrong wavelength, double-click the card in node view (single-shelf mode) or shelf
view (multishelf mode) to open the card view.

Step 6

Click the

Provisioning

>

Line

>

Wavelength Trunk Provisioning

tabs.

Step 7

In the Wavelength field, click the drop-down list and choose the correct wavelength.

Step 8

Click

Apply

.

If the wavelength does not appear because the wavelength band of the card, either C or L, differs from the band that was
provisioned in CTC, complete the following steps:

a) In the Wavelength field, click the drop-down list and choose

First Tunable Wavelength

.

b) Click

Apply

.

c) In the Wavelength field, click the drop-down list and choose the correct wavelength.
d) Click

Apply

.

If the alarm does not get cleared, you need to report a Service-Affecting (SA) problem. Log into the Technical Support
Website at

http://www.cisco.com/c/en/us/support/index.html

for more information or log into

http://www.cisco.com/c/

en/us/support/web/tsd-cisco-worldwide-contacts.html

to obtain a directory of toll-free Technical Support numbers for

your country.

WVL-UNLOCKED Alarm

Default Severity: Major (MJ), Service-Affecting (SA)

Logical Objects: TRUNK

The Wavelength Unlocked (WVL-UNLOCKED) alarm occurs when the laser cannot be tuned at the required
wavelength. This is a normal condition during laser frequency requests.

The alarm is cleared when the laser wavelength locker detects a lock condition during which the laser is
steadily tuned at the required wavelength.

DWDM Card LED Activity

The following sections list the DWDM card LED sequences during card insertion and reset.

DWDM Card LED Activity After Insertion

When an DWDM card is inserted in the shelf, the following LED activities occur:

1.

The FAIL LED illuminates for approximately 35 seconds.

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

439

Alarm Troubleshooting

WVL-UNLOCKED Alarm

«
...
483
484
485
486
487
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Бренд: Watchguard Страницы: 40

Mini Field Agent

Бренд: GE Страницы: 87

Бренд: Patton electronics Страницы: 51

Бренд: ICP DAS USA Страницы: 14

Бренд: ICP DAS USA Страницы: 25

Бренд: ICP DAS USA Страницы: 15

Бренд: ICP DAS USA Страницы: 8

Бренд: ICP Страницы: 14

Бренд: Yamaha Страницы: 6

Бренд: Yamaha Страницы: 4

Бренд: Yamaha Страницы: 22

Бренд: Yamaha Страницы: 49

Бренд: Stanwax Laser Страницы: 9

Fast SwitchHub-8mi SNMP

Бренд: Accton Technology Страницы: 13

Sentry Global Security Modem

Бренд: Server Technology Страницы: 22

kontron COMe-cEL6

Бренд: S&T Страницы: 99

Бренд: addlink Страницы: 9

1394 Dual-Port CardBus

Бренд: SIIG Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды