Cisco NCS 2000 series Скачать руководство пользователя страница 467 | Manualshive

Страница: 467 / 602

background image

DETAILED STEPS

Clear the remote client signal on the node.

If the condition does not clear, log into the Technical Support Website at

http://www.cisco.com/c/en/us/support/index.html

for more information or call Cisco TAC (1 800 553-2447).

TRUNK-PAYLOAD-MISM

Default Severity: Major (MJ), Service-Affecting (SA)

Logical Object: OCN, OTN, GE, FC

The TRUNK-PAYLOAD-MISM alarm is raised on the 10x10G-LC card, which is configured in the 10x10G
muxponder mode. This occurs when the payload types configured at the near-end and far-end nodes are
different.

Clear the TRUNK-PAYLOAD-MISM Alarm

Configure the same payload type at both near-end and far-end nodes.

SUMMARY STEPS

1.

Log in to a node on the network.

2.

In node view (single-shelf mode) or shelf view (multishelf mode), double-click the reporting card in CTC
to open the card view.

3.

Click the

Provisioning

>

Pluggable Port Modules

tabs.

4.

In the Pluggable Port Modules area, click

Create

.

5.

Choose the same payload type from the Port Type drop-down list and click

OK

.

DETAILED STEPS

Step 1

Log in to a node on the network.

Step 2

In node view (single-shelf mode) or shelf view (multishelf mode), double-click the reporting card in CTC to open the
card view.

Step 3

Click the

Provisioning

>

Pluggable Port Modules

tabs.

Step 4

In the Pluggable Port Modules area, click

Create

.

Step 5

Choose the same payload type from the Port Type drop-down list and click

OK

.

If the condition does not clear, log into the Technical Support Website at

http://www.cisco.com/c/en/us/support/index.html

for more information or call Cisco TAC (1 800 553-2447).

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

421

Alarm Troubleshooting

TRUNK-PAYLOAD-MISM

«
...
465
466
467
468
469
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Бренд: NEC Страницы: 72

Бренд: TDC Страницы: 27

ELECTRA ELITE IPK II

Бренд: NEC Страницы: 617

VERSA DOCK - SERVICE

Бренд: NEC Страницы: 8

ILDA Gem Laser projector tool

Бренд: Stanwax Laser Страницы: 3

Бренд: SUNRICH TECHNOLOGY Страницы: 5

APS6-400 Series

Бренд: Eaton Страницы: 114

Бренд: IEI Technology Страницы: 86

Lite N42B1P Series

Бренд: Dahua Technology Страницы: 14

Millennium P650

Бренд: Matrox Страницы: 54

IBOX-BAC Series

Бренд: IntesisBox Страницы: 2

WRT54GR - Wireless-G Broadband Router

Бренд: Linksys Страницы: 81

Бренд: VCS Страницы: 118

Бренд: Observint Страницы: 117

Бренд: TP-Link Страницы: 113

Бренд: VIA Technologies Страницы: 25

Бренд: Watchguard Страницы: 21

KÜHLER H2O 920

Бренд: Antec Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды