Cisco NCS 2000 series Скачать руководство пользователя страница 463 | Manualshive

Страница: 463 / 602

background image

the card sets the expected string to the value of the received string. If the alarm occurs on a port that has been
operating with no alarms, the circuit path has changed or someone entered a new incorrect value into the
Current Transmit String field. Complete the following procedure to clear either instance.

Clear the TIM-P Alarm

SUMMARY STEPS

1.

Complete the

Clear the TIM Alarm, on page 415

procedure. (The option will say Edit J1 Path Trace rather

than Edit J0 Path Trace.)

DETAILED STEPS

Complete the

Clear the TIM Alarm, on page 415

procedure. (The option will say Edit J1 Path Trace rather than Edit J0

Path Trace.)

If the alarm does not get cleared, you need to report a Service-Affecting (SA) problem. Log into the Technical Support
Website at

http://www.cisco.com/c/en/us/support/index.html

for more information or log into

http://www.cisco.com/c/

en/us/support/web/tsd-cisco-worldwide-contacts.html

to obtain a directory of toll-free Technical Support numbers for

your country.

TIM-S

Default Severity: Critical (CR), Service-Affecting (SA)

Logical Object: OCN

The TIM for Section Overhead alarm occurs when there is a mismatch between the expected and received J0
section overhead strings in either Manual or Auto mode.

In manual mode at the DS3/EC1-48 card Section Trace window, the user enters the expected string into the
Current Expected String field for the receiving port. The string must match the string typed into the Transmit
String field for the sending port. If these fields do not match, the login node raises the TIM-S alarm.

In Auto mode on the receiving port, the card sets the expected string to the value of the received string. If the
alarm occurs on a port that has been operating with no alarms, the circuit path has changed or someone entered
a new incorrect value into the Current Transmit String field. Complete the following procedure to clear either
problem.

TIM-S also occurs on a port that has previously been operating without alarms if someone switches the cables
or optical fibers that connect the ports. If TIM-S is enabled on the port, the

AIS-L , on page 116

alarm can be

raised downstream and the

RFI-L , on page 377

alarm can be raised upstream.

AIS-L and RFI-L are disabled or enabled in the

Provisioning

>

EC1

>

Section Trace

tab

Disable AIS/RDI

on TIM-S?

check box.

Note

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

417

Alarm Troubleshooting

Clear the TIM-P Alarm

«
...
461
462
463
464
465
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

BiPAC 4500NZ(L)

Бренд: Billion Страницы: 146

IES615-2D Series

Бренд: 3onedata Страницы: 3

Бренд: 3One data Страницы: 5

Бренд: 3onedata Страницы: 33

Бренд: Hama Страницы: 4

Бренд: Laird Страницы: 36

SteelCentral NetExpress

Бренд: Riverbed Страницы: 38

Бренд: NetComm Страницы: 69

Optane Persistent Memory 200 Series

Бренд: Supermicro Страницы: 54

Бренд: Paradyne Страницы: 6

Бренд: SeaLevel Страницы: 34

Бренд: Disc Makers Страницы: 38

Бренд: TP-Link Страницы: 131

Бренд: Omron Страницы: 6

Бренд: Aurora Страницы: 6

Бренд: ICOP Technology Страницы: 34

Бренд: Aviosys Страницы: 77

AirStation G54 WLA2-G54

Бренд: Buffalo Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды