Cisco NCS 2000 series Скачать руководство пользователя страница 448 | Manualshive

Страница: 448 / 602

background image

Step 3

If none of these alarms is reported, determine whether the local port reporting the SQUELCHED condition is in loopback.
(You will see LPBKFACILITY OR LPBKTERMINAL in the condition window for this port.) If it is in loopback,
complete the following steps:

a) In node view (single-shelf mode) or shelf view (multishelf mode), double-click the client card to open the card view.
b) Click the

Maintenance

>

Loopback

>

Port

tabs.

c) If the port Admin State column says OOS,MT (or Locked,maintenance) or OOS,DSBLD (or Locked,disabled), click

the cell to highlight it and choose IS (or Unlocked), from the drop-down list. Changing the state to

IS

(or

Unlocked

)

also clears any loopback provisioned on the port.

If the condition does not clear, log into the Technical Support Website at

http://www.cisco.com/c/en/us/support/index.html

for more information or call Cisco TAC (1 800 553-2447).

SSM-DUS

Default Severity: Not Alarmed (NA), Non-Service-Affecting (NSA)

Logical Object: TRUNK

The Synchronization Status (SSM) Message Quality Changed to Do Not Use (DUS) condition occurs on
ADM-10G and MXP trunk ports when the synchronization status message (SSM) quality level degrades to
DUS or is manually changed to DUS.

The signal is often manually changed to DUS to prevent timing loops from occurring. Sending a DUS prevents
the timing from being reused in a loop. The DUS signal can also be sent for line maintenance testing.

SSM-DUS is an informational condition and does not require troubleshooting.

Note

SSM-FAIL

Single Failure Default Severity: Minor (MN), Non-Service-Affecting (NSA); Double Failure Default Severity:
Major (MJ), Service-Affecting (SA)

Logical Object: TRUNK

The SSM Failed alarm occurs on ADM-10G and MXP trunk ports when the synchronization status messaging
received by the system fails. The problem is external to the NCS system. This alarm indicates that although
the ONS system is set up to receive SSM, the timing source is not delivering valid SSM messages.

Clear the SSM-FAIL Alarm

SUMMARY STEPS

1.

Verify that SSM is enabled on the external timing source.

2.

If timing is enabled, use an optical test set to determine that the external timing source is delivering SSM.
For specific procedures to use the test set equipment, consult the manufacturer.

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

402

Alarm Troubleshooting

SSM-DUS

«
...
446
447
448
449
450
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

AllShare Cast Dongle

Бренд: Samsung Страницы: 2

Бренд: D-Link Страницы: 14

Бренд: D-Link Страницы: 7

Бренд: D-Link Страницы: 41

Бренд: D-Link Страницы: 13

Бренд: D-Link Страницы: 99

Бренд: D-Link Страницы: 5

Бренд: D-Link Страницы: 15

AirPro DWL-6000AP

Бренд: D-Link Страницы: 65

Бренд: Data Translation Страницы: 98

Бренд: F-SECURE Страницы: 19

Module NI PXI-8250

Бренд: National Instruments Страницы: 39

Бренд: Lanner Страницы: 2

Бренд: Furuno Страницы: 24

MultiConnect SE MTS2EA

Бренд: Multitech Страницы: 8

Бренд: Fracarro Страницы: 12

MultiConnect SE MTS2EA

Бренд: Multitech Страницы: 2

Бренд: Lancom Страницы: 70

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды