Cisco NCS 2000 series Скачать руководство пользователя страница 417 | Manualshive

Страница: 417 / 602

background image

Clear the PWR-PROT-ON Alarm

SUMMARY STEPS

1.

To clear the alarm, check if the Raman amplifier is connected to the wrong span. If it is, check patch cords
setup and fix it.

2.

Alternatively, review the network configuration to see Raman amplifier has been wrongly used. If is,
remove it.

DETAILED STEPS

Step 1

To clear the alarm, check if the Raman amplifier is connected to the wrong span. If it is, check patch cords setup and fix
it.

Step 2

Alternatively, review the network configuration to see Raman amplifier has been wrongly used. If is, remove it.

If the alarm does not get cleared, you need to report a Service-Affecting (SA) problem. Log into the Technical Support
Website at

http://www.cisco.com/c/en/us/support/index.html

for more information or log into

http://www.cisco.com/c/

en/us/support/web/tsd-cisco-worldwide-contacts.html

to obtain a directory of toll-free Technical Support numbers for

your country.

RAMAN-CALIBRATION-FAILED

Default Severity: Minor (MN), Non-Service-Affecting (NSA)

Logical Object: OTS

The RAMAN-CALIBRATION-FAILED alarm is raised on the EDRA-1-xx, EDRA-2-xx, and RAMAN-CTP
cards when automatic Raman pump calibration is failed and will not run again. The alarm indicates insufficient
Raman Amplification by customer fibre. The Raman calibration can also fail due to the setup issues that
include:

• Wrong patch-cords or cabling

• Incorrect ANS

• Missing communication channel between nodes.

Clear the RAMAN-CALIBRATION-FAILED Alarm

SUMMARY STEPS

1.

Use optical time domain reflectometer (OTDR) to identity any excess loss between the Raman card
LINE-RX port and the customer fibre. After the inspection, a new Raman Calibration is triggered and if
the physical problem is fixed, the alarm will clear.

2.

If the alarm is caused by a set-up problem, re-verify all node installation steps and manually trigger a
Raman Calibration.

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

371

Alarm Troubleshooting

Clear the PWR-PROT-ON Alarm

«
...
415
416
417
418
419
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Бренд: ZETR Страницы: 2

Бренд: CallDirect Страницы: 33

BroadLink SP3353

Бренд: MicroNet Страницы: 66

IAR KickStart Kit TWR-K60N512-IAR

Бренд: IAR SYSTEMS Страницы: 8

Emulator MCU Board for 38D5 Group M38D59T-RLFS

Бренд: Renesas Страницы: 4

IMACS Network Device

Бренд: Zhone Страницы: 114

Бренд: Gemtek Systems Страницы: 51

Бренд: Kontron Страницы: 19

Бренд: RubyTech Страницы: 25

Бренд: QTech Страницы: 406

Бренд: Unex Страницы: 27

N-FXE 02B Series

Бренд: Lantronix Страницы: 10

Бренд: Camozzi Страницы: 22

Бренд: TRENDnet Страницы: 2

Бренд: Vxl Страницы: 4

Бренд: Airlinkplus Страницы: 24

Бренд: Roland Страницы: 224

Бренд: ADC Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды