Cisco NCS 2000 series Скачать руководство пользователя страница 399 | Manualshive

Страница: 399 / 602

background image

For more information about Ethernet cards, refer to the SDH Ethernet Card Software Feature and Configuration
Guide.

Note

Clear the PDI-P Condition

SUMMARY STEPS

1.

Verify that all circuits terminating in the reporting card are DISCOVERED:

2.

After determining that the circuit is DISCOVERED, ensure that the signal source to the card reporting
the alarm is working.

3.

If traffic is affected, complete the

Delete a Circuit, on page 454

procedure.

4.

Recreate the circuit with the correct circuit size. Refer to the Create Circuits and VT Tunnels chapter in
the Configuration guide for detailed procedures to create circuits.

5.

If circuit deletion and re-creation does not clear the condition, verify that there is no problem stemming
from the far-end OC-N card providing STS payload to the reporting card.

6.

If the condition does not clear, confirm the cross-connect between the OC-N card and the reporting card.

7.

If the condition does not clear, clean the far-end optical fiber according to site practice. If no site practice
exists, complete the procedure in the Maintain the Node chapter of the Configuration guide.

8.

If the condition does not clear, complete the

Physically Replace a Card, on page 453

procedure for the

optical/electrical cards.

DETAILED STEPS

Step 1

Verify that all circuits terminating in the reporting card are DISCOVERED:

a) Click the

Circuits

tab.

b) Verify that the

Status

column lists the circuit as active.

c) If the Status column lists the circuit as PARTIAL, wait 10 minutes for the NCS to initialize fully. If the PARTIAL

status does not change after full initialization, call Cisco TAC (1 800 553-247).

Step 2

After determining that the circuit is DISCOVERED, ensure that the signal source to the card reporting the alarm is
working.

Always use the supplied electrostatic discharge wristband when working with a powered NCS. Plug the wristband
cable into the ESD jack located on the lower-right edge of the shelf assembly.

Caution

Step 3

If traffic is affected, complete the

Delete a Circuit, on page 454

procedure.

Deleting a circuit can affect existing traffic.

Caution

Step 4

Recreate the circuit with the correct circuit size. Refer to the Create Circuits and VT Tunnels chapter in the Configuration
guide for detailed procedures to create circuits.

Step 5

If circuit deletion and re-creation does not clear the condition, verify that there is no problem stemming from the far-end
OC-N card providing STS payload to the reporting card.

Step 6

If the condition does not clear, confirm the cross-connect between the OC-N card and the reporting card.

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

353

Alarm Troubleshooting

Clear the PDI-P Condition

«
...
397
398
399
400
401
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Бренд: Panasonic Страницы: 18

X-Pedition 2000

Бренд: Enterasys Страницы: 86

Бренд: Measurement Computing Страницы: 27

Бренд: Cypress Semiconductor Страницы: 11

IBOX-BAC Series

Бренд: IntesisBox Страницы: 2

WRT54GR - Wireless-G Broadband Router

Бренд: Linksys Страницы: 81

Бренд: EVOC Страницы: 57

Speed Touch 591s

Бренд: Alcatel Страницы: 184

CNPS7000A Series

Бренд: ZALMAN Страницы: 9

Бренд: Rane Страницы: 128

Бренд: Acard Страницы: 34

Бренд: Shure Страницы: 113

SOUL CALIBUR II

Бренд: NAMCO Страницы: 26

Kontron SMARC-sXEL

Бренд: S&T Страницы: 108

Бренд: ZALMAN Страницы: 16

Бренд: DTS Страницы: 94

Бренд: B&B Electronics Страницы: 2

Бренд: Aerotech Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды