Cisco NCS 2000 series Скачать руководство пользователя страница 378

Страница: 378 / 602

Clear the OTDR-BASELINE-R-EXCEEDED-TX Alarm

The alarm is cleared automatically when one of the following conditions is satisfied:

• The reflectance event causing the alarm disappears.

• The reflectance event is below the threshold.

• The absolute threshold check is activated.

If the condition does not clear, log into the Technical Support Website at

http://www.cisco.com/c/en/us/support/index.html

for more information or call Cisco TAC (1 800 553-2447).

OTDR-FAST-FAR-END-IN-PROGRESS

Default Severity: Minor (MN)

Logical Object: EQUIPMENT

The OTDR-FAST-FAR-END-IN-PROGRESS alarm is raised when a fast scan is started on the remote side.

Clear the OTDR-FAST-FAR-END-IN-PROGRESS Alarm

Step 1

Wait until the scan on the remote side is completed. The time varies depending on the type of scan.

Step 2

Alternatively, stop the scan by navigating to:

Maintenance

DWDM

OTDR

; select the side where the scan is ongoing

and click

Cancel

. The scan is stopped on both the sides.

If the alarm does not clear, log into the Technical Support Website at

http://www.cisco.com/c/en/us/support/index.html

for more information or call Cisco TAC (1 800 553-2447).

OTDR-FAST-SCAN-IN-PROGRESS-RX

Default Severities: Minor (MI), Non-Service-Affecting (NSA)

Logical Object: EQPT

The Optical Time Domain Reflectometer (OTDR) Fast Scan In Progress Rx alarm is raised when the fast
OTDR scan starts in the Rx direction.

Clear the OTDR-FAST-SCAN-IN-PROGRESS-RX Alarm

Step 1

This alarm is cleared automatically when the fast OTDR scan in the RX direction is complete.

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

332

Alarm Troubleshooting

Clear the OTDR-BASELINE-R-EXCEEDED-TX Alarm

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание NCS 2000 series

Отзывы:

Похожие инструкции для NCS 2000 series

Бренды по названию

Популярные бренды

Cisco NCS 2000 series, Руководство по устранению неисправностей

Результаты поиска

Содержание NCS 2000 series

Отзывы:

Похожие инструкции для NCS 2000 series

Бренды по названию

Популярные бренды