Cisco NCS 2000 series Скачать руководство пользователя страница 263 | Manualshive

Страница: 263 / 602

background image

GFP-UP-MISMATCH

Default Severity: Major (MJ), Service-Affecting (SA)

Logical Object: CEMR, CE1000, CE100T, FCMR, GFP-FAC, ML1000, ML100T, MLFX

The GFP User Payload Mismatch is raised against Fibre Channel/FICON ports supporting GFP. It occurs
when the received frame user payload identifier (UPI) does not match the transmitted UPI and all frames are
dropped. The alarm is caused by a provisioning error, such as the port media type not matching the remote
port media type. For example, the local port media type could be set to Fibre Channel—1 Gbps ISL or Fibre
Channel—2 Gbps ISL and the remote port media type could be set to FICON—1 Gbps ISL or FICON—2
Gbps ISL.

Clear the GFP-UP-MISMATCH Alarm

SUMMARY STEPS

1.

Ensure that the transmit port and receive port are identically provisioned for distance extension by
completing the following steps:

2.

Ensure that both ports are set for the correct media type. For each port, complete the following steps:

DETAILED STEPS

Step 1

Ensure that the transmit port and receive port are identically provisioned for distance extension by completing the following
steps:

a) Double-click the card to open the card view.
b) Click the

Provisioning

>

Port

>

Distance Extension

tabs.

c) Check the check box in the

Enable Distance Extension

column.

d) Click

Apply

.

Step 2

Ensure that both ports are set for the correct media type. For each port, complete the following steps:

a) Double-click the card to open the card view (if you are not already in card view).
b) Click the

Provisioning

>

Port

>

General

tabs.

c) Choose the correct media type (

Fibre Channel - 1Gbps ISL

,

Fibre Channel - 2 Gbps ISL

,

FICON - 1 Gbps ISL

,

or

FICON - 2 Gbps ISL

) from the drop-down list.

d) Click

Apply

.

If the alarm does not get cleared, you need to report a Service-Affecting (SA) problem. Log into the Technical Support
Website at

http://www.cisco.com/c/en/us/support/index.html

for more information or log into

http://www.cisco.com/c/

en/us/support/web/tsd-cisco-worldwide-contacts.html

to obtain a directory of toll-free Technical Support numbers for

your country.

HELLO

Default Severity: Minor (MN), Non-Service-Affecting (NSA)

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

217

Alarm Troubleshooting

GFP-UP-MISMATCH

«
...
261
262
263
264
265
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Бренд: Lauterbach Страницы: 61

Бренд: Edge-Core Страницы: 7

Бренд: Dialogic Страницы: 2

Бренд: Xilica Audio Design Страницы: 30

Бренд: ZALMAN Страницы: 4

Бренд: ZyXEL Communications Страницы: 116

Бренд: Lanner electronics Страницы: 59

Бренд: Zalip Страницы: 77

EtherFast LNE100TX ver. 5

Бренд: Linksys Страницы: 42

Бренд: UTStarcom Страницы: 71

Бренд: Caen Страницы: 14

Бренд: Comelit Страницы: 19

Бренд: Microtek Страницы: 25

Бренд: Qlogic Страницы: 2

Бренд: Kordis Страницы: 31

ROADRECORDER 8400 NVR

Бренд: Safety Vision Страницы: 27

Бренд: SilverStone Страницы: 12

Бренд: Xilinx Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды