Cisco NCS 2000 series Скачать руководство пользователя страница 100 | Manualshive

Страница: 100 / 602

background image

Possible Cause

Username and password do not match.

Solution

Correct the username and password as described in the

Username or Password Do Not Match, on

Possible Cause

A lost DCC connection.

Solution

Usually accompanied by an embedded operations channel (EOC) alarm. Clear the EOC alarm and

verify the DCC connection as described in the EOC.

Java Runtime Environment Incompatible

Problem

The CTC application does not run properly.

Possible Cause

The compatible Java JRE is not installed.

Solution

The JRE contains the Java virtual machine, runtime class libraries, and Java application launcher that

are necessary to run programs written in the Java programming language. The NCS CTC is a Java application.
A Java application, unlike an applet, cannot rely completely on a web browser for installation and runtime
services. When you run an application written in the Java programming language, you need the correct JRE
installed. The correct JRE for each CTC software release is included on the Cisco NCS software CD. Complete
the

Launch CTC to Correct the Core Version Build, on page 55

. If you are running multiple CTC software

releases on a network, the JRE installed on the computer must be compatible with the different software
releases. The following table shows JRE compatibility with NCS software releases.

Table 8: JRE Compatibility for NCS

JRE 1.7

JRE 1.6

JRE 5.0

JRE 1.4

JRE 1.3

JRE 1.2.2

Software Release

Yes

Yes

No

No

No

No

NCS R10.0

Software Release 4.0 notifies you if an earlier JRE version is running on your PC or UNIX workstation.

Note

Launch CTC to Correct the Core Version Build

SUMMARY STEPS

1.

Exit the current CTC session and completely close the browser.

2.

Start the browser.

3.

Enter the NCS IP address of the node that reported the alarm. This can be the original IP address you
logged in with or an IP address other than the original.

4.

Log into CTC. The browser downloads the JAR file from CTC.

DETAILED STEPS

Step 1

Exit the current CTC session and completely close the browser.

Step 2

Start the browser.

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

54

General Troubleshooting

Java Runtime Environment Incompatible

«
...
98
99
100
101
102
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Бренд: XDS Страницы: 99

Бренд: D-Link Страницы: 11

Бренд: D-Link Страницы: 8

AirPlus DWL-810

Бренд: D-Link Страницы: 8

Бренд: D-Link Страницы: 12

Бренд: D-Link Страницы: 84

Бренд: GE Страницы: 93

Бренд: Eaton Страницы: 10

Бренд: Qualys Страницы: 2

Бренд: Salus Страницы: 16

Бренд: Zonet Страницы: 10

Бренд: Samsung Страницы: 65

HomePlug AV Ethernet Bridge PLE0200

Бренд: Abocom Страницы: 2

Бренд: U.S. Products Страницы: 80

PCH1 T P Series

Бренд: Parker Страницы: 107

Бренд: ProCurve Страницы: 2

AirStation WZR-1166DHP

Бренд: Buffalo Страницы: 2

EdgeRouter PoE ERPoe-5

Бренд: Ubiquiti Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды