Cisco NCS 1002 Скачать руководство пользователя страница 19

Страница: 19 / 68

Configure SSH

With a terminal emulation program, establish a SSH connection to the management interface port using its
IP address.

Before you begin

• Install the ncs1k-k9sec package on the NCS 1002. For details about package installation, see

Install

Packages, on page 49

• Generate the crypto key for SSH using the

crypto key generate dsa

command.

Procedure

Step 1

configure

Example:

RP/0/RP0/CPU0:ios# configure

Enters the Configuration mode.

Step 2

ssh server v2

Example:

RP/0/RP0/CPU0:ios(config)# ssh server v2

Enables the SSH server to accept only SSHv2 client connections.

Step 3

Use the

commit

end

command.

commit

-Saves the configuration changes and remains within the configuration session.

end

-Prompts user to take one of these actions:

•

Yes

-Saves configuration changes and exits the configuration session.

•

-Exits the configuration session without committing the configuration changes.

•

Cancel

-Remains in the configuration session, without committing the configuration changes.

Step 4

show ssh session details

Example:

RP/0/RP0/CPU0:ios# show ssh session details

Displays a detailed report of the SSHv2 connections to and from NCS 1002.

What to do next

Perform Clock Synchronization with NTP Server, on page 16

System Setup and Software Installation Guide for Cisco NCS 1002

Bring-up Cisco NCS 1002

Configure SSH

Содержание NCS 1002





































































Результаты поиска

Содержание NCS 1002

Отзывы:

Похожие инструкции для NCS 1002

Бренды по названию

Популярные бренды

Cisco NCS 1002, Руководство по настройке системы и установке программного обеспечения

Результаты поиска

Содержание NCS 1002

Отзывы:

Похожие инструкции для NCS 1002

Бренды по названию

Популярные бренды