Cisco N9K-C9336C-FX2-E Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 44

background image

Some power supplies have capabilities that are greater than the maximum power requirements for a switch.
To determine the power consumption characteristics for the switch, use the typical and maximum requirements
that are listed in the following table.

Note

Heat Dissipation
Requirement

Maximum Power
Consumption (AC or DC)

Typical Power
Consumption (AC or DC)

Switch

2453.330 BTUs per hour

719 W

337 W

Cisco Nexus
9336C-FX2-E

Power Specifications

Power specifications include the specifications for each type of power supply module.

750-W AC Power Supply Specifications

These specifications apply to the following power supplies:

• NXA-PAC-750W-PE

• NXA-PAC-750W-PI

Specification

Characteristic

750 W

Maximum output power

10 Amps at 100 VAC

Maximum input current

115 to 240 VAC nominal (Range: 90 to 264 VAC)

Rated input voltage

50 to 60 Hz nominal (Range: 47 to 63 Hz)

Rated input frequency

1100-W AC Power Supply Specifications

These specifications apply to the following power supplies:

• NXA-PAC-1100W-PE and PE2

• NXA-PAC-1100W-PI and PI2

Specification

Characteristic

Nominal range: 100 and 240 VAC (Range: 90-132
VAC, 180-264 VAC)

AC input voltage

Nominal range: 50 to 60 Hz (Range: 47-63 Hz)

AC input frequency

Cisco Nexus 9336C-FX2-E NX-OS Mode Switch Hardware Installation Guide

33

System Specifications

Power Specifications

«
...
35
36
37
38
39
...
»

Содержание N9K-C9336C-FX2-E













































Отзывы:

Нет отзывов

Похожие инструкции для N9K-C9336C-FX2-E

Бренд: D-Box Страницы: 27

Бренд: Labgear Страницы: 4

ALTUSCN KH1508I

Бренд: ATEN Страницы: 173

Бренд: Maiwe Страницы: 5

Бренд: Hama Страницы: 56

IPES-5208T-X Series

Бренд: Lantech Страницы: 39

Бренд: Ubiquiti Страницы: 23

Бренд: Exsys Страницы: 2

Бренд: Hama Страницы: 14

Бренд: KTI Страницы: 25

Бренд: Taiden Страницы: 4

Бренд: asas Страницы: 25

Бренд: Broadcast Tools Страницы: 10

Бренд: Lindy Страницы: 2

SUPERSTACK 3 3870 Series

Бренд: 3Com Страницы: 76

Бренд: I-Rocks Страницы: 23

Бренд: CYP Страницы: 32

950-2080 NEW STYLE GAS PRESSURE SWITCH

Бренд: TJERNLUND Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды