Cisco N9K-C93360YC-FX2 Скачать руководство пользователя страница 70

Страница: 70 / 72

Status

Color

LED

Port admin state is 'Enabled', SFP
is present and the interface is
connected (that is, cabled, and the
link is up).

Green

(port)

Port admin state is 'Disabled, or the
SFP is absent, or both.

Amber

Port admin state is 'Enabled' and
SFP is present, but interface is not
connected.

Off

Fan Module LEDs

The fan module LED is located below the air holes on the front of the module.

Status

Color

LED

The fan module is operational.

Green

STS

The fan module is not operational (fan is probably not functional).

Red

Fan module is not receiving power.

Off

Power Supply LEDs

The power supply LEDs are located on the left front portion of the power supply. Combinations of states

indicated by the Okay (

) and Fault (

) LEDs indicate the status for the module as shown in the following

table.

Status

LED

Power supply is on and outputting power to the switch.

Off

Green

Power supply is connected to a power source but not outputting power to the
switch—power supply might not be installed in the chassis.

Off

Flashing
green

Power supply is not receiving power.

Off

Power supply warning—possibly one of the following conditions:

• High voltage

• High power

• Low voltage

• Slow power supply fan

Flashing amber

Green

Cisco Nexus 93360YC-FX2 NX-OS Mode Switch Hardware Installation Guide

LEDs

Fan Module LEDs

Содержание N9K-C93360YC-FX2









































































Результаты поиска

Содержание N9K-C93360YC-FX2

Отзывы:

Похожие инструкции для N9K-C93360YC-FX2

Бренды по названию

Популярные бренды

Cisco N9K-C93360YC-FX2, Руководство по установке оборудования

Результаты поиска

Содержание N9K-C93360YC-FX2

Отзывы:

Похожие инструкции для N9K-C93360YC-FX2

Бренды по названию

Популярные бренды