Cisco N9K-C93360YC-FX2 Скачать руководство пользователя страница 67

Страница: 67 / 72

Photo

Cord Set Description

Part Number

Not applicable

All except Argentina, Brazil, and
Japan

No power cord included with
switch

NO-POWER-CORD

Table 1: HVAC/HVDC Power Cables Callout Table

Connect this end to the power supply unit.

DC Power Cable Specifications

Photo

Description

Part Number

The 930W DC power supply
(NXA-PDC-930W-PE/PI) is
shipped with cable
CAB-48DC-40A-8AWG.

NXA-PDC-930W-PE/PI

Regulatory Standards Compliance Specifications

The following table lists the regulatory standards compliance for the switch.

Table 2: Regulatory Standards Compliance: Safety and EMC

Description

Specification

Products should comply with CE Markings according to directives 2004/108/EC
and 2006/95/EC.

Regulatory compliance

• CAN/CSA-C22.2 No. 60950-1 Second Edition

• EN 60950-1 Second Edition

• IEC 60950-1 Second Edition

• AS/NZS 60950-1

• GB4943

Safety

Cisco Nexus 93360YC-FX2 NX-OS Mode Switch Hardware Installation Guide

System Specifications

DC Power Cable Specifications

Содержание N9K-C93360YC-FX2









































































Результаты поиска

Содержание N9K-C93360YC-FX2

Отзывы:

Похожие инструкции для N9K-C93360YC-FX2

Бренды по названию

Популярные бренды

Cisco N9K-C93360YC-FX2, Руководство по установке оборудования

Результаты поиска

Содержание N9K-C93360YC-FX2

Отзывы:

Похожие инструкции для N9K-C93360YC-FX2

Бренды по названию

Популярные бренды