Cisco N9K-C93180YC-FX Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 74

background image

Switch and Module Weights and Quantities

Quantity

Weight per Unit

Component

1

17.4 lb (7.9 kg)

Cisco Nexus 93180YC-FX Chassis (N9K-C93180YC-FX)

4

—

0.26 lb (0.12 kg)

Fan Module

– Port-side exhaust (blue) (NXA-FAN-30CCFM-F)

– Port-side intake (burgundy) (NXA-FAN-30CCFM-B)

2 (1 for
operations
and 1 for
redundancy)

—

2.42 lb (1.1 kg)

2.42 lb (1.1 kg)

2.42 lb (1.1 kg)

2.42 lb (1.1 kg)

2.42 lb (1.1 kg)

Power Supplies

– 500-W AC port-side exhaust (blue) (NXA-PAC-500W-PE)

– 500-W AC port-side intake (burgundy) (NXA-PAC-500W-PI)

– 1200-W HVAC/HVDC dual-direction (white) (N9K-PUV-1200W)

– 930-W DC port-side exhaust (blue) (NXA-PDC-930W-PE)

– 930-W DC port-side intake (burgundy) (NXA-PDC-930W-PI)

Transceiver and Cable Specifications

To determine which transceivers, adapters, and cables are supported by this switch, see

https://www.cisco.com/

c/en/us/support/interfaces-modules/transceiver-modules/products-device-support-tables-list.html

.

To see the transceiver specifications and installation information, see

https://www.cisco.com/c/en/us/support/

interfaces-modules/transceiver-modules/products-device-support-tables-list.html

.

Switch Power Input Requirements

The following table lists the typical amount of power that the switch consumes. It also lists the maximum
amount of power that you must provision for the switch and power supply for peak conditions.

Some power supplies have capabilities that are greater than the maximum power requirements for a switch.
To determine the power consumption characteristics for the switch, use the typical and maximum requirements
that are listed in the following table.

Note

Heat Dissipation
Requirement

Maximum Power
Consumption (AC or DC)

Typical Power
Consumption (AC or DC)

Switch

1450.16 BTUs per hour

425 W

260 W

Cisco Nexus
93180YC-FX

Cisco Nexus 93180YC-FX ACI-Mode Switch Hardware Installation Guide

48

System Specifications

Switch and Module Weights and Quantities

«
...
56
57
58
59
60
...
»

Содержание N9K-C93180YC-FX











































































Отзывы:

Нет отзывов

Похожие инструкции для N9K-C93180YC-FX

Бренд: CAME Страницы: 2

Бренд: Qlogic Страницы: 135

SANbox2 SANbox2-64

Бренд: Qlogic Страницы: 224

Бренд: Radial Engineering Страницы: 8

Бренд: Radial Engineering Страницы: 2

Бренд: H3C Страницы: 77

S5130-EI Series

Бренд: H3C Страницы: 32

Бренд: YOKOGAWA Страницы: 74

Бренд: IOGear Страницы: 40

InSwitch ISM-P Series

Бренд: InHand Страницы: 81

Бренд: AV Link Страницы: 2

Peripheral Sharer 2 to 1

Бренд: Black Box Страницы: 35

Бренд: Comprehensive Страницы: 6

Бренд: Wantec Страницы: 4

Luzense RADIM RF

Бренд: Unilamp Страницы: 2

Бренд: Cooper Crouse-Hinds Страницы: 24

Бренд: Rose electronics Страницы: 80

Бренд: mind alive Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды