Cisco MX200 G2 Скачать руководство пользователя страница 85

Страница: 85 / 141

D15332.01 MX200 G2 and MX300 G2 Administrator Guide CE8.0, NOVEMBER 2015.

Cisco TelePresence MX200 G2 and MX300 G2

Administrator Guide

Network [1] TrafficControl Mode

Define the network traffic control mode to decide how to control the video packets

transmission speed.

Requires user role: ADMIN
Default value: On

Value space: Off/On

Off: Transmit video packets at link speed.
On: Transmit video packets at maximum 20 Mbps. Can be used to smooth out bursts in

the outgoing network traffic.

Network [1] VLAN Voice Mode

Define the VLAN voice mode. The VLAN Voice Mode will be set to Auto automatically if you

have Cisco UCM (Cisco Unified Communications Manager) as provisioning infrastructure.

Note that Auto mode will NOT work if the NetworkServices CDP Mode setting is Off.

Requires user role: ADMIN
Default value: Auto

Value space: Auto/Manual/Off

Auto: The Cisco Discovery Protocol (CDP), if available, assigns an id to the voice VLAN. If

CDP is not available, VLAN is not enabled.
Manual: The VLAN ID is set manually using the Network VLAN Voice VlanId setting. If

CDP is available, the manually set value will be overruled by the value assigned by CDP.
Off: VLAN is not enabled.

Network [1] VLAN Voice VlanId

Define the VLAN voice ID. This setting will only take effect if Network VLAN Voice Mode is

set to Manual.

Requires user role: ADMIN
Default value: 1

Value space: Integer (1..4094)

Set the VLAN voice ID.

Introduction

Configuration

Peripherals

Maintenance

System settings

Appendices



System settings

Содержание MX200 G2














































































































































Результаты поиска

Содержание MX200 G2

Отзывы:

Бренды по названию

Популярные бренды

Cisco MX200 G2, Руководство администратора

Результаты поиска

Содержание MX200 G2

Отзывы:

Бренды по названию

Популярные бренды