Cisco MX200 G2 Скачать руководство пользователя страница 5

Страница: 5 / 141

D15332.01 MX200 G2 and MX300 G2 Administrator Guide CE8.0, NOVEMBER 2015.

Cisco TelePresence MX200 G2 and MX300 G2

Administrator Guide

Products covered in this guide

• Cisco TelePresence MX200 G2
• Cisco TelePresence MX300 G2

User documentation

This guide provides you with the information required to

administrate the endpoint. How to install the endpoint is covered

in the

Installation guide,

and the required initial configurations are

described in the

Getting started guide

Refer to the

►

User documentation on the Cisco web site

appendix for more information about the guides for this endpoint.

Downloading the user documentation

We recommend you visit the Cisco web site regularly for updated

versions of the guides:

►

http://www.cisco.com/go/mx-docs

Software

Download software for the endpoint from the Cisco web site:

►

http://www.cisco.com/cisco/software/navigator.html

We recommend reading the Software release notes (CE8):

►

http://www.cisco.com/c/en/us/support/collaboration-

endpoints/telepresence-mx-series/tsd-products-support-

series-home.html

User documentation and software

Introduction

Configuration

Peripherals

Maintenance

System settings

Appendices



Introduction

Содержание MX200 G2














































































































































Результаты поиска

Содержание MX200 G2

Отзывы:

Бренды по названию

Популярные бренды

Cisco MX200 G2, Руководство администратора

Результаты поиска

Содержание MX200 G2

Отзывы:

Бренды по названию

Популярные бренды