manualshive.com logo in svg

Cisco MX200 G2, Руководство администратора

Поделиться
Скачать
Cisco MX200 G2 Скачать руководство пользователя страница 112

D15332.01 MX200 G2 and MX300 G2 Administrator Guide CE8.0, NOVEMBER 2015.  

www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved. 

112

Cisco TelePresence MX200 G2 and MX300 G2

Administrator Guide

Video DefaultLayoutFamily Remote

Select which video layout family to be used for the remote participants.

Requires user role: ADMIN
Default value: Auto

Value space: Auto/Equal/Prominent/Overlay/Single

Auto: The default layout family, as given by the local layout database, will be used as the 

remote layout. 
Equal: The Equal layout family will be used as the remote layout. All videos have equal 

size, as long as there is space enough on the screen.
Prominent: The Prominent layout family will be used as the remote layout. The active 

speaker, or the presentation if present, will be a large picture, while the other participants 

will be small pictures. Transitions between active speakers are voice switched.
Overlay: The Overlay layout family will be used as the remote layout. The active speaker, 

or the presentation if present, will be shown in full screen, while the other participants 

will be small pictures-in-picture (PiP). Transitions between active speakers are voice 

switched.
Single: The active speaker, or the presentation if present, will be shown in full screen. 

The other participants are not shown. Transitions between active speakers are voice 

switched.

Video DefaultMainSource

Define which video input source shall be used as the main video source.

Requires user role: USER
Default value: 1

Value space: 1/2/3

Set the source to be used as the main video source.

Video Input Connector [1..4] CameraControl Mode

Define whether the camera that is connected to this video input connector can be 

controlled or not.
Note that camera control is not available for Connector 2 (HDMI), Connector 3 (HDMI) and 

Connector 4 (DVI-I).

Requires user role: ADMIN
Default value: Connector 1: On   Connector 2,3,4: Off

Value space: Connector 1: Off/On   Connector 2,3,4: Off

Off: Disable camera control.
On: Enable camera control.

Video Input Connector [1..4] CameraControl CameraId

The camera ID is a unique identifier of the cameras that are connected to the video input.

Requires user role: ADMIN
Default value: 1

Value space: 1

The camera ID is fixed and cannot be changed.

Introduction

Configuration

Peripherals

Maintenance

System settings

Appendices

System settings

Содержание MX200 G2














































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды