manualshive.com logo in svg

Cisco MX200 G2, Руководство администратора

Поделиться
Скачать
Cisco MX200 G2 Скачать руководство пользователя страница 104

D15332.01 MX200 G2 and MX300 G2 Administrator Guide CE8.0, NOVEMBER 2015.  

www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved. 

104

Cisco TelePresence MX200 G2 and MX300 G2

Administrator Guide

Standby settings

Standby Control

Define whether the system should go into standby mode or not.

Requires user role: ADMIN
Default value: On

Value space: Off/On

Off: The system will not enter standby mode.
On: The system will enter standby mode when the Standby Delay has timed out. 

Requires the Standby Delay to be set to an appropriate value.

Standby Delay

Define how long (in minutes) the system shall be in idle mode before it goes into standby 

mode. Requires the Standby Control to be enabled.

Requires user role: ADMIN
Default value: 10

Value space: Integer (1..480)

Set the standby delay (minutes).

Standby BootAction

Define the camera position after a restart of the codec.

Requires user role: ADMIN
Default value: DefaultCameraPosition

Value space: None/RestoreCameraPosition/DefaultCameraPosition

None: No action.
RestoreCameraPosition: When the video system restarts, the camera returns to the 

position that it had before the restart.
DefaultCameraPosition: When the video system restarts, the camera moves to the 

factory default position.

Standby StandbyAction

Define the camera position when going into standby mode.

Requires user role: ADMIN
Default value: PrivacyPosition

Value space: None/PrivacyPosition

None: No action.
PrivacyPosition: When the video system enters standby, the camera turns to a sideways 

position for privacy.

Standby WakeupAction

Define the camera position when leaving standby mode.

Requires user role: ADMIN
Default value: RestoreCameraPosition

Value space: None/RestoreCameraPosition/DefaultCameraPosition

None: No action.
RestoreCameraPosition: When the video system leaves standby, the camera returns to 

the position that it had before entering standby.
DefaultCameraPosition: When the video system leaves standby, the camera moves to 

the factory default position.

Introduction

Configuration

Peripherals

Maintenance

System settings

Appendices

System settings

Содержание MX200 G2














































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды