Cisco MX Series Скачать руководство пользователя страница 32

Страница: 32 / 33

Cisco TelePresence Video Systems

D15318.02 Video Systems Getting Started Guide CE8.1, APRIL 2016.

Getting Started Guide

User documentation for the Cisco TelePresence

products is available at



http://www.cisco.com/go/telepresence/docs

Choose a product category in the right pane until you find

the correct product. This is the path you have to follow:

Collaboration Room Endpoints >

Cisco TelePresence MX Series

TelePresence Integration Solutions >

Cisco TelePresence SX Series

Alternatively, use the following short-link to find the

documentation:



http://www.cisco.com/go/mx-docs



http://www.cisco.com/go/sx-docs

The documents are organized in the following categories:

Install and Upgrade > Install and Upgrade Guides

•

Installation guides:

How to install the product

•

Getting started guide:

Initial configurations required to get

the system up and running

•

RCSI guide:

Regulator y compliance and safety

information

Maintain and Operate > Maintain and Operate Guides

•

Getting started guide:

Initial configurations required to get

the system up and running

•

Administrator guide:

Information required to administer

your product

•

Administering CE Endpoints on CUCM:

Tasks to perform

to start using the product with the Cisco Unified

Communications Manager (CUCM)

Maintain and Operate > End-User Guides

•

User guides:

How to use the product

•

Quick reference guides:

How to use the product

•

Physical interface guide:

Details about the product’s

physical interface, including the connector panel and

LEDs.

Reference Guides | Command references

•

API reference guides:

Reference guide for the Application

Programmer Interface (API)

Reference Guides > Technical References

•

CAD drawings:

2D CAD drawings with measurements

Design > Design Guides

•

Video conferencing room guidelines:

General guidelines

for room design and best practice

•

Video conferencing room guidelines:

Things to do to

improve the perceived audio quality

Software Downloads, Release and General Information >

Licensing Information

•

Open source documentation:

Licenses and notices for

open source software used in this product

Software Downloads, Release and General Information >

Release Notes

•

Software release notes

User documentation on the Cisco web site

Introduction

User interfaces

Web interface

On-screen setup assistant

Appendices



Touch

Appendices

Содержание MX Series


































Результаты поиска

Содержание MX Series

Отзывы:

Бренды по названию

Популярные бренды

Cisco MX Series, Руководство по началу работы

Результаты поиска

Содержание MX Series

Отзывы:

Бренды по названию

Популярные бренды